topic HP-UX 11.11 cold install hangs on rp3410 in Operating System - HP-UX

HP-UX 11.11 cold install hangs on rp3410

Krueger, Ulf — Tue, 21 Mar 2006 09:14:10 GMT

Hi everybody,

I have a problem performig a cold install with HP-UX 11.11. I need a clean installation of this version. This version also was pre-installed on this machine.

After I boot (and swith Fast Boot=ON, SEARCH and BOOT P0 for CD-Rom) it starts to load the INSTALL. After a while it displays memory configuration and then it hangs:

Configuration Menu: Enter command > search

Searching for potential boot device(s)
This may take several minutes.

To discontinue search, press any key (termination may not be immediate).

IODC
Path# Device Path (dec) Device Path (mnem) Device Type Rev
----- ----------------- ------------------ ----------- ----
P0 0/0/2/0.0 ide.0 Random access media 1

P1 0/1/1/0.1 intscsia.1 Random access media 1

Configuration Menu: Enter command >
Configuration Menu: Enter command > BO P0
Interact with IPL (Y, N, or Cancel)?> n

Booting...
Boot IO Dependent Code (IODC) revision 1

HARD Booted.

ISL Revision A.00.43 Apr 12, 2000

ISL booting hpux (;0):INSTALL

Boot
: disk(0/0/2/0.0.0.0.0.0.0;0):WINSTALL
11751424 + 1970264 + 2631464 start 0x200d68

alloc_pdc_pages: Relocating PDC from 0xfffffff0f0c00000 to 0x3f700000.
gate64: sysvec_vaddr = 0xc0002000 for 2 pages
NOTICE: nfs3_link(): File system was registered at index 4.
NOTICE: autofs_link(): File system was registered at index 6.
NOTICE: cachefs_link(): File system was registered at index 7.
igelan0: INITIALIZING HP PCI 1000Base-T Core at hardware path 0/1/2/0

System Console is on the Built-In Serial Interface
Swap device table: (start & size given in 512-byte blocks)
entry 0 - auto-configured on root device; ignored - no room
WARNING: no swap device configured, so dump cannot be defaulted to primary swap.
WARNING: No dump devices are configured. Dump is disabled.

Starting the STREAMS daemons-phase 1
Create STCP device files
$Revision: vmunix: vw: -proj selectors: CUPI80_BL2000_1108 -c 'V
w for CUPI80_BL2000_1108 build' -- cupi80_bl2000_1108 'CUPI80_BL2000_1108' Wed
Nov 8 19:24:56 PST 2000 $
Memory Information:
physical page size = 4096 bytes, logical page size = 4096 bytes
Physical: 1046528 Kbytes, lockable: 716044 Kbytes, available: 843920 Kbytes

I would be very happy for any ideas, what I can investigate to get more details.

Ulf

Re: HP-UX 11.11 cold install hangs on rp3410

harry d brown jr — Tue, 21 Mar 2006 09:33:38 GMT

What is the date on your media for 11.11?

How long have you waited?

Have you tried to interact with IPL (dictate where you want the root disk to be).

live free or die
harry d brown jr

Re: HP-UX 11.11 cold install hangs on rp3410

Steven E. Protter — Tue, 21 Mar 2006 10:11:23 GMT

Shalom,

Try booting off of P1.

That may be the cd drive, not P0

SEP

Re: HP-UX 11.11 cold install hangs on rp3410

Krueger, Ulf — Tue, 21 Mar 2006 11:21:07 GMT

Hi again,

1. date on media is december 2004
version B11.11 version 1
I waited over week-end!

2. No, I did not try interactive with IPL
What can the advantage be?

Thank You very much!

Ulf

Re: HP-UX 11.11 cold install hangs on rp3410

Krueger, Ulf — Tue, 21 Mar 2006 11:27:23 GMT

P1 is hard drive. P0 is CD rom - I can see
start booting from CD rom.

Re: HP-UX 11.11 cold install hangs on rp3410

Joshua Scott — Tue, 21 Mar 2006 11:47:54 GMT

Ulf,

Try turning off FASTBOOT and rebooting. I have seen memory errors cause hangs like this.

Josh

Re: HP-UX 11.11 cold install hangs on rp3410

Sanjay_6 — Tue, 21 Mar 2006 17:58:42 GMT

Hi,

do you have a 11i version other than Dec 2004 to try.

Take a look at this thread below from ITRC.

http://www1.itrc.hp.com/service/cki/docDisplay.do?docLocale=en_US&docId=200000077246045

The ITRC doc id is WO050125_CW01

Hope this helps.

regds

Re: HP-UX 11.11 cold install hangs on rp3410

Krueger, Ulf — Wed, 22 Mar 2006 10:43:43 GMT

Turning off FASTBOOT did not help.

Unfortunately I do not have newer medias,
but I have ordered them...

The ITRC doc id is WO050125_CW01 looks
very appropriate, because I have this
graphics adapter installed in my rp3410.

Is there a chance to burn a patched install
media containing PHKL_30306?

Re: HP-UX 11.11 cold install hangs on rp3410

Sanjay_6 — Wed, 22 Mar 2006 11:05:09 GMT

Hi,

I do not think it is possible to burn a media with the patch. You may have to wait for the new media to arrive. If you have installation CD's in place of DVD, you can try with that. It may help.

Hope this helps.

regds

Re: HP-UX 11.11 cold install hangs on rp3410

Andy Torres — Wed, 22 Mar 2006 11:12:19 GMT

Your ISL revision is a little old. Isn't it around A.00.45 now? If you're just waiting for the new media, maybe you could load the latest firmware patch and try again, just for giggles.

Re: HP-UX 11.11 cold install hangs on rp3410

Krueger, Ulf — Tue, 11 Apr 2006 04:54:12 GMT

Today, I received HP-UX 11i Version 1 dated to September 2005 on cd rom and re-tested the cold installation as I did before.

I still have the same firmware as before!

I still turn fastboot on!

... And it works! WINSTALL does not hang anymore...

Thanks to all!!!