topic Re: Vpar software upgrade landed in panic-Urgent in Operating System - HP-UX

Vpar software upgrade landed in panic-Urgent

vasanth_2 — Sun, 20 Sep 2009 12:17:15 GMT

Dear all,

I am in upgrading process of vPar software version from A.03.03 to A.03.05. After installing the software system crashed with the below error. Please help asap.

MON> vparload -p vPar1 -b /stand/vmunix
[MON] Booting vPar1...

[MON] vPar1 loaded

Stored message buffer up to panic:

System Panic:

linkstamp: Sun Sep 20 08:51:46 EDT 2009
_release_version: @(#) $Revision: vmunix: vw: -proj selectors: CUPI80_BL2000_1108 -c 'Vw for CUPI80_BL2000_1108 build' -- cupi80_bl2000_1108 'CUPI80_BL2000_1108' Wed Nov 8 19:24:56 PST 2000 $
panic: Incompatible vPar monitor version

PC-Offset Stack Trace (read across, top of stack is 1st):

[MON]
[MON] vPar1 has halted.
MON> [MON] vPar2 has halted.

Re: Vpar software upgrade landed in panic-Urgent

Stephan._1 — Sun, 20 Sep 2009 12:47:46 GMT

Hi,
could you give some more information?

OS Version?

PA-RISC / Integrity?

Did you make the update of the vPar software on every vPar?

Re: Vpar software upgrade landed in panic-Urgent

Torsten. — Sun, 20 Sep 2009 13:17:38 GMT

>> Incompatible vPar monitor version

Did you already boot the vpmon?

Re: Vpar software upgrade landed in panic-Urgent

Torsten. — Sun, 20 Sep 2009 13:22:15 GMT

Regarding the more information request - it is hp-ux 11.11 on PA-RISC, because of the version.

Re: Vpar software upgrade landed in panic-Urgent

Stephan._1 — Sun, 20 Sep 2009 13:28:15 GMT

Thanks @Torsten, i don't have the compability matrix in my mind, so i prefer to ask :-p

@vasanth
Did you follow the procedure on page 85?

http://www.docs.hp.com/en/T1335-90057/T1335-90057.pdf

Re: Vpar software upgrade landed in panic-Urgent

Prashanth.D.S — Sun, 20 Sep 2009 18:38:32 GMT

Hi Vasanth

The error message itself should indicate you that the version of Vpar software installed is not matching with the vpmon being booted before launching any vpar..

The following can be checked to better determine what is occurring:

- setboot

The setboot output should display hardware path of the disk the monitor is being booted from.

Example:

# setboot
Primary bootpath : 0/0/4/0/0/4/0.12.0
Alternate bootpath : 0/0/0/3/0.6.0
Autoboot is ON (enabled)
Autosearch is ON (enabled)

- what /stand/vpmon

The "what" output when run on the disk the monitor is booted from should display the version of the Vpar monitor. Example:

# what /stand/vpmon
/stand/vpmon:
$Revision: vpmon: vw: -- selectors: R11.11_BL2003_1103 'cup2_vpar_pib6' 'cup2_muralid_a.03.04.06' Thu Jan 11 20:22:26 PST 2007 $
$Revision: vpmon: vw: -- selectors: R11.11_BL2003_1103 'cup2_vpar_pib6' 'cup2_muralid_a.03.04.06' Thu Jan 11 20:22:26 PST 2007 $
$Revision: libdebug.a: vw: -- selectors: R11.11_BL2003_1103 'cup2_vpar_pib6' 'cup2_muralid_a.03.04.06' Thu Jan 11 20:21:53 PST 2007 $
$Revision: libfs.a: vw: -- selectors: R11.11_BL2003_1103 'cup2_vpar_pib6' 'cup2_muralid_a.03.04.06' Thu Jan 11 20:21:50 PST 2007 $
$Revision: libinit.a: vw: -- selectors: R11.11_BL2003_1103 'cup2_vpar_pib6' 'cup2_muralid_a.03.04.06' Thu Jan 11 20:21:44 PST 2007 $
$Revision: libinit-pdk.a: vw: -- selectors: R11.11_BL2003_1103 'cup2_vpar_pib6' 'cup2_muralid_a.03.04.06' Thu Jan 11 20:22:24 PST 2007 $
$Revision: libio.a: vw: -- selectors: R11.11_BL2003_1103 'cup2_vpar_pib6' 'cup2_muralid_a.03.04.06' Thu Jan 11 20:21:36 PST 2007 $
$Revision: libio-pdk.a: vw: -- selectors: R11.11_BL2003_1103 'cup2_vpar_pib6' 'cup2_muralid_a.03.04.06' Thu Jan 11 20:21:25 PST 2007 $
$Revision: libipmi.a: vw: -- selectors: R11.11_BL2003_1103 'cup2_vpar_pib6' 'cup2_muralid_a.03.04.06' Thu Jan 11 20:21:16 PST 2007 $
$Revision: libldr-pdk.a: vw: -- selectors: R11.11_BL2003_1103 'cup2_vpar_pib6' 'cup2_muralid_a.03.04.06' Thu Jan 11 20:22:17 PST 2007 $
$Revision: libmem.a: vw: -- selectors: R11.11_BL2003_1103 'cup2_vpar_pib6' 'cup2_muralid_a.03.04.06' Thu Jan 11 20:21:13 PST 2007 $
$Revision: libmem-pdk.a: vw: -- selectors: R11.11_BL2003_1103 'cup2_vpar_pib6' 'cup2_muralid_a.03.04.06' Thu Jan 11 20:21:08 PST 2007 $
$Revision: libpdc-pdk.a: vw: -- selectors: R11.11_BL2003_1103 'cup2_vpar_pib6' 'cup2_muralid_a.03.04.06' Thu Jan 11 20:22:09 PST 2007 $
$Revision: libpdcem.a: vw: -- selectors: R11.11_BL2003_1103 'cup2_vpar_pib6' 'cup2_muralid_a.03.04.06' Thu Jan 11 20:22:04 PST 2007 $
$Revision: libsvc.a: vw: -- selectors: R11.11_BL2003_1103 'cup2_vpar_pib6' 'cup2_muralid_a.03.04.06' Thu Jan 11 20:21:05 PST 2007 $
$Revision: libsvc-pdk.a: vw: -- selectors: R11.11_BL2003_1103 'cup2_vpar_pib6' 'cup2_muralid_a.03.04.06' Thu Jan 11 20:22:00 PST 2007 $
$Revision: libutil-pdk.a: vw: -- selectors: R11.11_BL2003_1103 'cup2_vpar_pib6' 'cup2_muralid_a.03.04.06' Thu Jan 11 20:21:57 PST 2007 $
vp_config.c $Date: 2004/10/14 17:52:10 $Revision: r11.11/8

NOTE: The above output shows the monitor with version A.03.04.06.

- liflcp /dev/rdsk/c#t#d#:AUTO - -> where c#t#d# is the device file for you boot disk.

Example:

# lifcp /dev/dsk/c8t12d0:AUTO -
hpux /stand/vpmon -a

NOTE: The previous lifcp example output confirms that the system is booting from the Vpar monitor /stand/vpmon .

- what /stand/vmunix | grep â I vpar

Example:

# what /stand/vmunix | grep -I vpar
$Revision: libvpar-pdk.a: vw: -- selectors: R11.11_BL2003_1103 'cup2_vpar_pib6' 'cup2_muralid_a.03.04.06' Thu Jan 11 20:18:01 PST 2007 $

NOTE: The "what" on the running kernel shows that the Virtual Partitions version is A.03.04.06, which matches the vpar monitor version from the previous example.

- vparstatus -v -p

vparstatus will display the BOOT path for the given vpar. It will also display the kernel from which it is being booted.

For this case, the BOOT path for the vpar pointed to a different hardware path than setboot. The BOOT disk from vparstatus configured for the given vpar contained an earlier version of the Virtual Partition software, which explained the mismatch.

The vpar successfully booted for this case after using vparcreate -p chx009a1 -a io:0/0/4/0/0/4/0.12.0:BOOT to set the vpar's boot path the same as the Npar's primary boot path from which the monitor was booted.

--------------------------------------------------------------------------------

Re: Vpar software upgrade landed in panic-Urgent

vasanth_2 — Sun, 20 Sep 2009 19:52:30 GMT

Dear svo, Torsten and Prashanth,

Thanks for all your quick replies. I found the issue and definitely my mistake. Its a software incompatibility b/w vPar software and the vpmon. I forgot that vpmon will be updated only after restarting the Npar. After rebooting the vpmon things went well.

Thanks a tons again
ITRC forums and members rocks!! keep rocking!!!

Vasanth

Re: Vpar software upgrade landed in panic-Urgent

vasanth_2 — Sun, 20 Sep 2009 19:55:43 GMT

After giving the command reboot from MON promt everthing started without any issues.

MON>reboot

Issue Solved