topic Re: Itanium 2660 boot problem in Operating System - HP-UX

Itanium 2660 boot problem

wayne_104 — Wed, 02 Feb 2011 08:12:01 GMT

When I rebooted the system this morning i got the error.

Loading.: HP-UX Primary Boot: 0/1/1/0.0x8114db7e708ea57.0x0
Load of HP-UX Primary Boot: 0/1/1/0.0x8114db7e708ea57.0x0 failed: Not Found
Press any key to continue

in efi
Device mapping table
blk0 : Acpi(HWP0002,PNP0A03,0)/Pci(2|1)/Usb(0, 0)
blk1 : Acpi(HWP0002,PNP0A03,0)/Pci(2|0)/Usb(2, 2)
blk2 : Acpi(HWP0002,PNP0A03,200)/Pci(1|0)/Scsi(Pun8,Lun0)

blk2:\> blk2:

blk2:\> ls
ls: Cannot open current directory - No mapping
Exit status code: No mapping

What can i do to recover from this?

I have done many reboots before this.

Re: Itanium 2660 boot problem

Torsten. — Wed, 02 Feb 2011 08:17:45 GMT

The system doesn't the boot disk.
From EFI shell do

Shell> reconnect -r

Shell> map -r

Do you boot from local disk?

Are the disks on thge "default" controller or on an optional P400?

(Shell> devtree
will tell)

Is there a hardware RAID configured?

Re: Itanium 2660 boot problem

wayne_104 — Wed, 02 Feb 2011 11:02:37 GMT

Yes there is a hardware raid configured and the raid controller and the mirror are all fine

Re: Itanium 2660 boot problem

Torsten. — Wed, 02 Feb 2011 11:05:30 GMT

Did the reconnect and map command help?

After firmware update or other events the RAID could be disabled, go into the controller BIOS and check. Activate if needed.

Re: Itanium 2660 boot problem

wayne_104 — Wed, 02 Feb 2011 11:09:55 GMT

yea the raid is active

been rebboting fine till this morning.
Adapter PCI PCI PCI FW Revision Status || Bus Dev Fnc || SAS1068 01 01 00 1.16.33.00-IR Enabled

Adapter SAS1068 || PCI Address(Bus/Dev/Func) 01:01:00 || MPT Firmware Revision 1.16.33.00-IR || SAS Address 50060B00:00BE62C0 || Status Enabled || Boot Support [Enabled BIOS & OS] || || RAID Properties || || SAS Topology || || Advanced Adapter Properties ||

Array 1 of 1 || Identifier HP IR Volume HP01 || Type IM || Scan Order 8 || Size(MB) 69618 || Status Optimal || || Manage Array || || Slot Device Identifier RAID Hot Drive Pred Size || Num Disk Spr Status Fail (MB) || 1 HP DH072ABAA6 HPD4 Yes No Primary No 69618 || 2 HP DG146BB976 HPDC Yes No Secondary No 69618

Re: Itanium 2660 boot problem

Torsten. — Wed, 02 Feb 2011 11:24:14 GMT

I still don't know about reconnect and map command results ...

However, maybe some of your action before damaged the EFI area. In this case you probably need to use the recovery shell and repair it.

Re: Itanium 2660 boot problem

wayne_104 — Wed, 02 Feb 2011 12:13:16 GMT

how do i do that?

Re: Itanium 2660 boot problem

Torsten. — Wed, 02 Feb 2011 12:24:15 GMT

Boot from the install DVD and select the recovery shell.

Re: Itanium 2660 boot problem

wayne_104 — Wed, 02 Feb 2011 12:52:46 GMT

Thanks know that have not done it on a 11.31.

Is it intuitive?

Re: Itanium 2660 boot problem

Ismail Azad — Wed, 02 Feb 2011 17:09:03 GMT

Hi,

> Is it intuitive?

Depends on what you want to do on the recovery shell but a part of the interactive interface makes things a little easier. Remember to do this you have to recognize your DVD on EFI boot manager and get into the "recovery shell", the same procedure for installing from a DVD only a different option.

Regards
Ismail Azad

Re: Itanium 2660 boot problem

wayne_104 — Thu, 03 Feb 2011 05:37:17 GMT

Thanks guys

Tried looking for a doc could only get an old one.

Any links to a new one.

Re: Itanium 2660 boot problem

georgek_1 — Thu, 03 Feb 2011 06:16:11 GMT

Hi,

This link may help you .
http://docstore.mik.ua/manuals/hp-ux/en/5992-5309/ch15s03.html

Regards,

George

Re: Itanium 2660 boot problem

DeafFrog — Thu, 03 Feb 2011 06:23:49 GMT

Hi Wayne ,

check this link
http://h20000.www2.hp.com/bizsupport/site/search/r4_0/jsp/search.jsp?lang=en&cc=us&prodSeriesId=3257036&prodTypeId=15351&tx=Ignite+UX+manual&pc=0&sc=2&cm=1&nh=10&rf=0&lkc=1&lk=1

download the ignite ux admin guide.(2nd on the page )

page 272 , hope this helps .

regards,
Rahul

Re: Itanium 2660 boot problem

wayne_104 — Thu, 03 Feb 2011 07:45:40 GMT

This is what i am getting now

Selection: b
Entering boot area repairing...

Loading commands necessary for boot recovery...

idisk: Primary partition information not valid.
Run idisk with -r option to restore.
The verification failed. Trying to restore
the partitions of /dev/rdsk/c16t0d0.

Restoring Primary Header and Table from Alternate.
Restoration of partitions on /dev/rdsk/c16t0d0 completed OK.

Verification of partitions on /dev/rdsk/c16t0d0 completed OK.

Running mkboot to verify/repair boot areas.

Specifying -e option requires devices files for EFI and HP-UX partitions.
Specifying -e option requires devices files for EFI and HP-UX partitions.
mkboot failed.

Re: Itanium 2660 boot problem

wayne_104 — Thu, 03 Feb 2011 08:20:32 GMT

any suggestions or is it reinstall time?

Re: Itanium 2660 boot problem

Ismail Azad — Thu, 03 Feb 2011 08:33:47 GMT

Hi,

Since mkboot has failed, it seems like you will not be able to load the boot utilities as that is what mkboot does. Similar thing was previously mentioned by Torsten. I think you have a problem with your boot area now. This could be as bad as having a missing auto file, corrupt label file etc. Since you mentioned it, if you don't have time to troubleshoot and repair your BDRA as it is called, go with the old saying that saves you time.. "Dont troubleshoot just reinstall". I wouldn't take that route but you mentioned it!. Because not everyone can REINSTALL. :)

From the error you are getting something serioulsly looks wrong with your partition table.

Regards
Ismail Azad

Re: Itanium 2660 boot problem

wayne_104 — Thu, 03 Feb 2011 08:40:01 GMT

Not what i wanted to hear but i have tried all options and will put me out my misery.