topic Re: HP Integrity BL860c i2, unable to install HP-UX 11i v3 in Operating System - HP-UX

HP Integrity BL860c i2, unable to install HP-UX 11i v3

Aamir_Majeed — Mon, 04 Jun 2012 16:23:48 GMT

Hi,

I am installing new HP Integrity BL860c i2, while installing I am getting following error;

WARNING: Could not find Q_BOOT device. Cannot determine what the boot device was.

I also notice following error;

krs_read_mfs: Error 5 opening MFS

I am using externelly powered, USB DVD ROM via front SUV port on server blade.

I have tried different media also, in order to isolate this issue but no luck. Please find detailed output;

       * Preparing to execute init...
======= 06/04/12 05:19:04 EDT HP-UX Installation Initialization.
         @(#)Ignite-UX Revision C.7.14.264
         @(#)ignite/launch (opt) Revision:
         /branches/IUX_RA1203/ignite/src@84394 Last Modified: 2012-01-25
         13:38:44 +0530 (Wed, 25 Jan 2012)
       * Configuring RAM filesystems...
       * Scanning system for IO devices...
       * Boot device is:
WARNING: Could not find Q_BOOT device. Cannot determine what the boot device
         was.
WARNING: Could not find source device in ioscan output. You must select from
         the list of devices below to use for the source device:
index       HW-path         Class   description
0) 0/0/0/1/0/0/4        usb        HP_UHCI_Virtual_Controller
1) 0/0/0/2/0/0/0        ext_bus    PCIe_SAS_SmartArray_P410i_RAID_Controller
2) 0/0/0/2/0/0/0.0x0.0x4000000000000000 disk       HP_LOGICAL_VOLUME
3) 0/0/0/3/0/0/0        lan        HP_PCIe_2-p_10GbE_Built-in
4) 0/0/0/3/0/0/1        lan        HP_PCIe_2-p_10GbE_Built-in
5) 0/0/0/4/0/0/0        lan        HP_PCIe_2-p_10GbE_Built-in
6) 0/0/0/4/0/0/1        lan        HP_PCIe_2-p_10GbE_Built-in
7) 0/0/0/5/0/0/0        fc         HP_451871-B21_8Gb_Dual_Port_PCIe_Fibre_Channel_Mezzanine_(FC_Port_1)
8) 0/0/0/5/0/0/1        fc         HP_451871-B21_8Gb_Dual_Port_PCIe_Fibre_Channel_Mezzanine_(FC_Port_2)
9) 0/0/0/29/0           usb        Intel_UHCI_Controller
10) 0/0/0/29/1           usb        Intel_UHCI_Controller
11) 0/0/0/29/7           usb        Intel_EHCI_64-bit_Controller
12) 0/0/0/30/0/4/0       graphics   PCI_Display_(1002515e)
13) 0/120                processor Processor
14) 0/122                processor Processor
15) 0/124                processor Processor
16) 0/126                processor Processor
17) 64000/0x0/0x0        escsi_ctlr USB_Mass_Storage_Virt_Ctlr

Enter the index corresponding to the device to use
as the installation source, 'r' to rescan, or 'q' to reboot:

I was using Device listed at no. 17 but same error, similery I have tried after rebooting server, but same issue

[ilo009c0229e1ea] CM:hpiLO-> sysrev

SYSREV

Revisions Active Pending

-------------------------------------

iLO FW : 01.51.03

System FW : 01.90

MHW FPGA : 02.00

Power Mon FW : 03.04

Front Panel HW : 04.00

PRS HW : 02.07

IOH HW : 02.02

Pleas help, thanks in advance.

Re: HP Integrity BL860c i2, unable to install HP-UX 11i v3

S_Logan — Tue, 05 Jun 2012 15:40:57 GMT

Hi Aamir,

Did you try to rescan the device?

HTH,

Surendar

Re: HP Integrity BL860c i2, unable to install HP-UX 11i v3

S_Logan — Tue, 05 Jun 2012 15:48:33 GMT

Hi Aamir,

If rescan works , its well and good else please update the USB driver and check the system.

HTH,

Surendar

Was the post useful? Click on the WHITE KUDOS! Star.

For HP Guided Troubleshooting: http://www.hp.com/support/hpgt

Re: HP Integrity BL860c i2, unable to install HP-UX 11i v3

Michael Leu — Thu, 07 Jun 2012 14:53:34 GMT

As a workaround you could try the iLO Virtual Media:

Stick the DVD into your PC.
Open iLO in your Browser.
Navigate to "Virtual Media".
Click on the "Launch" button in the top right corner (easy to miss).

This is for iLO 01.41.01 (I'm not on 01.51.03 yet)

Re: HP Integrity BL860c i2, unable to install HP-UX 11i v3

Dave Cast — Tue, 26 Nov 2013 00:45:00 GMT

SAME ISSUE!!!!! Over and over...NO rescan doesn't help! NO rebooting doesn't help! NO it doesn't matter what device I pick, same error: could not find q_boot device...blah blah {esoteric} nonsense.

HP needs their feet held to the fire for making garbage like this - it's 2013 HP - dvd roms have been around for awhile.

Re: HP Integrity BL860c i2, unable to install HP-UX 11i v3

Torsten. — Tue, 26 Nov 2013 10:19:52 GMT

This was a known problem with older installation media (bad driver, IIRC).
Some more details would be useful - FW versions, install media release, etc ...

Re: HP Integrity BL860c i2, unable to install HP-UX 11i v3

JayroSaycon — Thu, 28 Nov 2013 09:12:08 GMT

Before, we also encountered issues and difficulty installing 11.31 using external DVD drive and always ending up failed.

It happened because we are using NON-HP model of external DVD drive. Upon purchasing and using HP model DVD drive, then it just worked everything perfectly. Now onwards, I still preferr to use any HP DVD drive model when it needed.

Cheers!