topic Re: Hp-UX rp 3440 Not booting after network change-Urgent in Operating System - HP-UX

Hp-UX rp 3440 Not booting after network change-Urgent

mansa06 — Mon, 18 Jun 2007 09:12:12 GMT

Hi,
We are having Hp-UX rp 3440.
We changed the network setting from static into dyanmic in the file /etc/rc.config.d/netconf DHCP_client=1 , removed the static ip and restarted the machine.
After that machine not booting, keep on showing "RV200 P/N 113-88304-100 BIOS" message.
Can any one help on this issue?
Note: We are not able to connect Console IP also?
Since this is urgent any one help on this issue?
Thanks
Saravanan

Re: Hp-UX rp 3440 Not booting after network change-Urgent

Court Campbell — Mon, 18 Jun 2007 09:22:29 GMT

Can you get to the serial console?

Re: Hp-UX rp 3440 Not booting after network change-Urgent

mansa06 — Mon, 18 Jun 2007 09:40:21 GMT

No, I am not able to get serial console.
What shall I do?
Regards
Saravanan

Re: Hp-UX rp 3440 Not booting after network change-Urgent

Steven E. Protter — Mon, 18 Jun 2007 09:52:01 GMT

Shalom,

Get on the console and reverse the changes with set_parms

The change you said you made should not have disabled lan console access.

There may be something else wrong with the system. As noted above you may need to connect a serial console to gain access

SEP

Re: Hp-UX rp 3440 Not booting after network change-Urgent

Denver Osborn — Mon, 18 Jun 2007 09:55:23 GMT

It's going to be nearly impossible to troubleshoot the system without console access to see the system startup.

Do you know if it was able to obtain a dynamic ip? If so can you ping that address or try to ssh to it?

I'm guessing the "RV200 P/N..." message is from a monitor attached to graphics card, right? You wouldn't see any output until after CDE or Xserver starts up, which may not happen if the network or name resolution is a problem.

Get a null modem cable and a laptop w/ hyperterm to troubleshoot things.

-denver

Re: Hp-UX rp 3440 Not booting after network change-Urgent

Fabian Briseño — Mon, 18 Jun 2007 09:58:18 GMT

Hella mansa06.

see if these links help.

http://forums1.itrc.hp.com/service/forums/questionanswer.do?threadId=1119379

http://docs.hp.com/en/AB551-96002/AB551-96002_Rev_A_Install.pdf

http://docs.hp.com/en/AB551-90003/AB551-90003.pdf

Re: Hp-UX rp 3440 Not booting after network change-Urgent

Srinivas Thokala_1 — Tue, 19 Jun 2007 09:11:00 GMT

Did you commentedout the IP line in /etc/hosts file?
If you don't have local/remote console access, from where did you see the error message after rebooting?
You may have to backout the plan and verify the network configuration.

-Srinivas

Re: Hp-UX rp 3440 Not booting after network change-Urgent

Torsten. — Tue, 19 Jun 2007 09:24:01 GMT

BTW, what could be a good reason to use DHCP for a server?

Re: Hp-UX rp 3440 Not booting after network change-Urgent

mansa06 — Thu, 21 Jun 2007 05:51:15 GMT

Thanks for all yours reply.
We connected that hp-ux machine into serial port and changed the n/w configuration and now machine able to boot.

Thanks
Saravanan

Re: Hp-UX rp 3440 Not booting after network change-Urgent

Bill Hassell — Thu, 21 Jun 2007 08:55:06 GMT

And just to reinforce the question about using DHCP: your server will be almost useless every time it reboots using DHCP because no user will know how to connect to it unless you have a clever DHCP system administrator and a dynamic DNS server that is 100% reliable. And of course, your system will hang if the DHCP server doesn't work or is unreachable at bootup. Never use DHCP on a server.