topic Re: Ifconfig: bad value in Operating System - HP-UX

Ifconfig: bad value

Juan Carlos Malizia — Wed, 26 Sep 2001 13:12:44 GMT

Hi,
I'm having problems to configure a lan card (100BT) in a HP-9000 L2000 running HP-UX 11.0.
The fact is that it refuses to set a specific netmask value of 255.255.255.192 but in the other hand it accepts masks such as 255.255.255.0 or 255.255.255.240.
The command I'm using is:
ifconfig lan1 192.168.31.39 netmask 255.255.255.192 up
Any suggestion?
Thanks in advance!
Juan Carlos

Re: Ifconfig: bad value

Robin Wakefield — Wed, 26 Sep 2001 13:21:59 GMT

Hi Juan Carlos,

Try disabling subnet mask checking:

ndd -set /dev/ip ip_check_subnet_addr 0

To make permanent, edit /etc/rc.config.d/nddconf:
TRANSPORT_NAME[0]=ip
NDD_NAME[0]=ip_check_subnet_addr
NDD_VALUE[0]=0

Rgds, Robin.

Re: Ifconfig: bad value

someone_4 — Wed, 26 Sep 2001 13:28:31 GMT

Hold Juan ..
If disabling subnet mask checking works
dont forget to edit your
/etc/rc.config.d/netconf file
it will look like this

INTERFACE_NAME[0]=lan0
IP_ADDRESS[0]=your.info.here
SUBNET_MASK[0]=your.info.here
BROADCAST_ADDRESS[0]=your.info.here
INTERFACE_STATE[0]=up
DHCP_ENABLE[0]=0

Richard

Re: Ifconfig: bad value

Ravi_8 — Wed, 26 Sep 2001 13:51:33 GMT

Hi Juan

doing in this may work
#ifconfig lan1 ip_addr netmask x.x.x.x broadcast x.x.x.x
#ifconfig lan1 up

and also make the entry in file /etc/rc.config.d/netconf as suggested by richard

Re: Ifconfig: bad value

Sanjay_6 — Wed, 26 Sep 2001 14:17:59 GMT

Hi Juan,

Have you tried it through SAM.

Thanks

Re: Ifconfig: bad value

Sridhar Bhaskarla — Wed, 26 Sep 2001 15:01:15 GMT

As per general theory, your subnetting is valid. with 2 subnet bits, you are supposed to get 4 subnets with 62 hosts each. This particular case falls under the range 192.168.31.1 - 192.168.31.62 with the subnet being 192.168.31.0 broadcasting to 192.168.31.63. I don't know what's with HP declining this subnet mask.

The only way around is ignoring the subnet mask check by setting ip_check_subnet_addr to 0 using ndd.

-Sri

Re: Ifconfig: bad value

rick jones — Wed, 26 Sep 2001 17:18:03 GMT

the reason HP-UX is rejecting the maxk/ip combination is it was interpreting them under the original, classful subnetting rules that still had the concept ofa this netowrk, all subnets broadcast. thus, an all-zeros or all-ones subnet portion could not be assigned as a host's IP address.

the ip_check_subnet_addr as mentioned will cause the mask/ip combinations to be interpreted under the newer classless rules. that becomes the default in 11i.

don't forget to put ip_check_subnet_addr in the nddconf file...

Re: Ifconfig: bad value

Anthony deRito — Wed, 26 Sep 2001 19:26:25 GMT

To reiterate what Rick was saying you got snagged by RFC1122. This RFC states that no subnet bits of an IP address can use all zeros or all ones.

So in other words, you are trying to split up your network into 4 subnets using 255.255.255.192 however the first and the last are illegal according to RFC1122 because the first has 00 as its subnet bits and the last have 11 as its subnet bits.

The reason why 255.255.255.0 works is because its a standard subnet mask and the reason that 255.255.255.240 works is that 192.168.31.39 is now in the third subnet which does not contain all zeros or all ones. In other words, the third subnet is 0011 and that is legal because it does not break the RFC1122 rule.

Tony