topic Re: Swagentd Daemon Not Enabled!!! in Operating System - HP-UX

Swagentd Daemon Not Enabled!!!

johnsonjthomas — Tue, 16 Feb 2010 16:08:49 GMT

Hi

I am currently working on the performance tuning of TBB 2.2 on HPUX Itanium platform. For this purpose I am trying to install caliper on HPUX. Unfortunately I am stuck with an error which I am not able to figure out. The error is as follows:

Could not start a management session for "nitkhp01:/ake*". The system administrator for host "nitkhp01" may have disabled the
swagentd daemon or there may be a networking problem affecting the operation. If the swagentd daemon has been disabled, it can be
enabled by the system administrator on "nitkhp01" by setting the "SW_ENABLE_SWAGENTD" entry in /etc/rc.config.d/swconfig to "1" and
executing "/usr/sbin/swagentd -r".

This error was encountered while installing caliper.depot.gz file on HPUX using the command swinstall -s /path/caliper.depot.gz. We tried to enable the swagentd daemon according to how it is given but still we are facing with the same problem. Actually speaking the daemon is running all the time, somehow its not able to detect that the daemon is running. It would be very helpful if anyone could help.

Re: Swagentd Daemon Not Enabled!!!

Steven E. Protter — Tue, 16 Feb 2010 16:17:21 GMT

Shalom,

ll /etc/nsswitch.conf

If it is not there, there are a few choices with the name nsswitch as the first part of the name.

By default, new installations of HP-UX do not have an nsswitch.conf set. You need to put one in place and then restart swagentd.

Though maybe not required, I recommend:

gunzip calilper.gz

swinstall -s /tmp/caliper.gz \*

Then run swinstall. swinstall may be able to gunzip depots, but I have never tested this.

SEP

Re: Swagentd Daemon Not Enabled!!!

Dennis Handly — Tue, 16 Feb 2010 16:33:37 GMT

>SEP: Though maybe not required, I recommend:
>gunzip caliper.depot.gz
>swinstall -s /path/caliper.depot \*

Yes, it's required.

>swinstall may be able to gunzip depots

It doesn't. It can handle individual files in the depot that are already compressed but not the whole tape depot.

Re: Swagentd Daemon Not Enabled!!!

johnsonjthomas — Tue, 16 Feb 2010 16:51:51 GMT

Hi steven,

Thanks for the quick reply.I have the latest version of HPUX (11.31) and it does not have nsswitch.conf. Where can I get the nsswitch.conf file for this purpose or what should I do in order to make such a file?

Re: Swagentd Daemon Not Enabled!!!

Steven E. Protter — Tue, 16 Feb 2010 17:08:10 GMT

Shalom again,

cd /etc

ll nsswitch*

Pick one that meets your needs.
more, cat or vi edit them.

cp nsswitch. /etc/nsswitch.conf

Then restart the swagentd daemon

SEP

Re: Swagentd Daemon Not Enabled!!!

johnsonjthomas — Wed, 17 Feb 2010 05:44:12 GMT

Hi steven

I did according to what you said.
The files present are

nsswitch.files
nsswitch.nis
nsswitch.compat
nsswitch.ldap
nsswitch.hp_defaults

I did not change anything in the files. I directly copied into /etc/nsswitch.conf and restarted swagentd daemon. Tried swinstall but still it gives the same error.

Could you tell me how to find out to what kind of client is my host configured to (I mean whether is it configured to NIS or LDAP since the corresponding nsswitch files are present)?

Re: Swagentd Daemon Not Enabled!!!

johnsonjthomas — Wed, 17 Feb 2010 06:19:26 GMT

Hi,

I tried setting nsswitch.files as /etc/nsswitch.conf and then restarted the daemon and swinstalled it.

The errors were encountered:

ERROR: RPC exception: "Communications failure (dce / rpc)" 02/17/10 11:51:16 IST
ERROR: Could not start a management session for "nitkhp01:/". The system administrator for host "nitkhp01" may have disabled the swagentd daemon or there may be a networking problem affecting the operation. If the swagentd daemon has been disabled, it can be enabled by the system administrator on "nitkhp01" by setting the "SW_ENABLE_SWAGENTD" entry in /etc/rc.config.d/swconfig to "1" and executing "/usr/sbin/swagentd -r".
* Target connection failed for "nitkhp01:/".
ERROR:More information may be found in the daemon logfile on this target (default location is nitkhp01:/var/adm/sw/swagentd.log).
* Selection had errors.

I am totally stuck at this point since I am not able to install anything on the HPUX machine because of this problem. Any help regarding this issue would be great.

Re: Swagentd Daemon Not Enabled!!!

Johnson Punniyalingam — Wed, 17 Feb 2010 06:30:38 GMT

can you run the below command

/usr/sbin/swagentd -r

Re: Swagentd Daemon Not Enabled!!!

johnsonjthomas — Wed, 17 Feb 2010 06:31:57 GMT

thats the same command as swagentd -r rite????

Re: Swagentd Daemon Not Enabled!!!

johnsonjthomas — Wed, 17 Feb 2010 06:43:15 GMT

I tried the above command also but am getting the same error.

Re: Swagentd Daemon Not Enabled!!!

Kapil Jha — Wed, 17 Feb 2010 07:22:15 GMT

Can you stop and the restart the daemon.

BR,
Kapil+

Re: Swagentd Daemon Not Enabled!!!

smatador — Wed, 17 Feb 2010 08:55:37 GMT

Hi,
I don't think that .gz is the cause of this error because even a management session could not start. So the solution is to be sure that the swagentd is ok.
Look for ps -ef | grep sw
And kill all session sw. Look at the date of the swagentd. When you do a swagentd -r the date of the daemon is updated. So you could also kill the swagentd to be sure and restart it.
After that gunzip the depot and install it.
HTH

Re: Swagentd Daemon Not Enabled!!!

Robert-Jan Goossens — Wed, 17 Feb 2010 13:24:40 GMT

Hi,

Could you post your /etc/hosts and the /etc/rc.config.d/netconf file.

Regards,
Robert-Jan

Re: Swagentd Daemon Not Enabled!!!

Dennis Handly — Wed, 17 Feb 2010 14:01:23 GMT

>smatador: I don't think that .gz is the cause of this error

Better to fix all of the simple problems before tackling the hard SD networking issues.

Re: Swagentd Daemon Not Enabled!!!

johnsonjthomas — Thu, 18 Feb 2010 06:00:28 GMT

Hi Robert,

The contents of the files are as follows:

/etc/hosts

172.16.41.25 nitkhp01
127.0.0.1 localhost loopback
172.16.41.26 nitkhp01

I have attached the file /etc/rc.config.d/netconf

Re: Swagentd Daemon Not Enabled!!!

johnsonjthomas — Thu, 18 Feb 2010 06:17:38 GMT

Hi

I have found that when executing ps -ef|grep sw, it shows that the process /usr/sbin/swagentd -r is still running and there is no swagentd daemon running. Does anyone know as to why the /usr/sbin/swagentd -r process is still runnning without starting the daemon?

Thanks

Re: Swagentd Daemon Not Enabled!!!

Kapil Jha — Thu, 18 Feb 2010 06:57:35 GMT

-r
The restart option stops the currently running daemon and restarts a new daemon. Because the swagentd daemon processes options only at startup, you must restart the daemon after you have modified any daemon options. Otherwise, the modified options have no effect.

-r only restart the daemon, what we are asking here is kill the process and restart it again.

BR,
Kapil+

Re: Swagentd Daemon Not Enabled!!!

johnsonjthomas — Thu, 18 Feb 2010 07:08:09 GMT

Hi Kapil

That is exactly what I am doing. I killed the process and restart it using swagentd -r command but strangely it shows that the process running is "swagentd -r" and the daemon never starts (I mean the process "swagentd -r" is running instead of restarting the swagentd daemon).

Thanks

Re: Swagentd Daemon Not Enabled!!!

Dennis Handly — Thu, 18 Feb 2010 08:47:56 GMT

>Better to fix all of the simple problems

For a gzipped file, you get different more obvious errors:
$ swlist -s $PWD/ffox_A20019ar02_ia.depot.gz
ERROR: tar: /var/tmp/ffox_A20019ar02_ia.depot.gz:
This doesn't look like a tar archive

Re: Swagentd Daemon Not Enabled!!!

johnsonjthomas — Thu, 18 Feb 2010 09:10:22 GMT

Could anyone explain me as to why "swagentd -r" process is running and not the daemon swagentd when I give a "swagentd -r" command. I have attached the output file of "ps -ef" showing the output before executing "swagentd -r" and after executing "swagentd -r" in order to give a clear idea to what I am saying. Any help would be great.

Thanks