topic SGeSAP Error in Operating System - HP-UX

SGeSAP Error

Alexander Santamaria Ji — Wed, 14 Oct 2009 05:01:17 GMT

I am configuring a cluster with SGeSAP in HPUX 11.31 and have the following error message when trying to start dbSID or ciSID package:

Oct 13 11:57:37 PM - Node "PROD": (check_parameters): ERROR: Package appears to
be specified without virtual IP addresses
Oct 13 11:57:37 PM - Node "PROD": (check_parameters): ERROR: Check IP[] array in
package control file and verify the
Oct 13 11:57:37 PM - Node "PROD": (check_parameters): ERROR: call syntax in cust
omer_defined_run_commands section

Re: SGeSAP Error

Suraj K Sankari — Wed, 14 Oct 2009 05:04:58 GMT

HI,
See the below threade which is having the same problem
http://forums11.itrc.hp.com/service/forums/questionanswer.do?threadId=1023628

Suraj

Re: SGeSAP Error

Alexander Santamaria Ji — Wed, 14 Oct 2009 05:05:35 GMT

I attach the sap.config file

Re: SGeSAP Error

melvyn burnard — Wed, 14 Oct 2009 06:48:12 GMT

Well here is the clue:
Package appears to be specified without virtual IP addresses
Oct 13 11:57:37 PM - Node "PROD": (check_parameters): ERROR: Check IP[] array in package control file

In your attached file:

# DBRELOC
# Maps to the virtual IP address of the database instance.
# Make sure to use the same syntax as in the IP[] array
# of the package control file.
#
# Example:
DBRELOC=172.16.1.8 <<<-----

So you have specified this in your sap confi8g file, but have you set it in the package control file......???

Re: SGeSAP Error

Michael Leu — Wed, 14 Oct 2009 07:46:41 GMT

If you have SGeSAP 05.00 check that you have PHSS_39358 installed.

Re: SGeSAP Error

Michael Leu — Wed, 14 Oct 2009 08:02:34 GMT

Sorry about my short reply above. In SGeSAP 05.00 they have quite a bad scripting error in the first few lines of sapwas.cntl. This gets fixed with PHSS_39358.

I vaguely remember that the error messages was about IP[] values not being set, so the stuff above might apply.

Also check that the sapwas.cntl is called with a . (dot) as described in the guides.

Re: SGeSAP Error

Alexander Santamaria Ji — Wed, 14 Oct 2009 14:08:21 GMT

Hi all,

I already installed the Patch PHSS_39358.

This is the configuration included in the dbPRD.control.script file:

IP[0]=172.16.1.8
SUBNET[0]=172.16.0.0

function customer_defined_run_cmds
{
. /etc/cmcluster/PRD/sapwas.cntl start PRD
test_return 51
}
.....
function customer_defined_halt_cmds
{
. /etc/cmcluster/PRD/sapwas.cntl stop PRD
test_return 52
}

And in the sap.config file:

NFSRELOC=172.16.1.9
DBRELOC=172.16.1.8
CINAME=DVEBMGS
CINR=00
CIRELOC=172.16.1.7

I am trying to configure 3 packages with SGeSAP:

ciPRD
dbPRD
sapnfs

also have configured a ciPRD.control script file and a sapnfs.control.script file.

Sugestions?

Alexander

Re: SGeSAP Error

Alexander Santamaria Ji — Mon, 19 Oct 2009 18:35:40 GMT

Â¡I Solved my problem!

Installing the patch PHSS_39358 and copying the original files to the cluster directory
/etc/cmcluster/ and /etc/cmcluster, then including the specific information in each package files (for dbSID, ciSID).

Thanks for your help.

Re: SGeSAP Error

Alexander Santamaria Ji — Mon, 19 Oct 2009 18:38:55 GMT

Installing patch PHSS_39358, copyng the new files from /opt/cmcluster to /etc/cmcluster and /etc/cmcluster/, then including the information in each package file.