topic Re: cmquerycl not work in Operating System - HP-UX

cmquerycl not work

gigiz — Thu, 24 Jul 2008 08:21:30 GMT

Hi
i have 2 host.
I want create a cluster .
When i do:
cmquerycl -v -C cmclconf.ascii -n ncpbmte1 -n ncpbees1

It failed with this error:
Timed out trying to query the following disk(s) on node ncpbmte1
/dev/dsk/c91t7d6
/dev/dsk/c91t7d7
/dev/dsk/c91t8d0
/dev/dsk/c91t8d1
/dev/dsk/c91t8d2
/dev/dsk/c91t8d3

Timed out trying to query the following disk(s) on node ncpbmte1
/dev/dsk/c88t2d7
/dev/dsk/c88t3d0
/dev/dsk/c88t3d1
/dev/dsk/c88t3d2
/dev/dsk/c88t3d3
/dev/dsk/c88t3d4
Note: Disks were discovered which are not in use by either LVM or VxVM.
Use pvcreate(1M) to initialize a disk for LVM or,
use vxdiskadm(1M) to initialize a disk for VxVM.

And not create cmclconf.ascii.
I have:
S.O. 11.23
ServiGuard 11.18 with patch PHSS_37601
I have configured cmclnodelist
I have check identd in /etc/inetd.conf
If i do cmquerycl -C cmclconf.ascii -n ncpbees1
it work and create a cmclconf.ascci for one node.
If i do cmquerycl -C cmclconf.ascii -n ncpbmte1
not work.
Help me!!! many point at all good response.

Re: cmquerycl not work

Jeeshan — Thu, 24 Jul 2008 08:49:21 GMT

did you create pv with those disks?

i guess you have configure those disks but without create pv and belongs those on any VG and without create any file system.

check your cluster configuration file.

Re: cmquerycl not work

melvyn burnard — Thu, 24 Jul 2008 09:47:11 GMT

Well there appears to be a problem querying certain devices on each node, as per the comment:
Timed out trying to query the following disk(s) on node ncpbmte1
So you need to find out WHY it cannot query these disks.
On node ncpbmte1 go use ioscan etc to verify these devices.

Ignore the comment:
Note: Disks were discovered which are not in use by either LVM or VxVM.
Use pvcreate(1M) to initialize a disk for LVM or, use vxdiskadm(1M) to initialize a disk for VxVM.

This is just an informative message.
You could, if needed, add inthe -k option to cmquerycl to reduce disk probing.

Re: cmquerycl not work

Pedro Cirne — Thu, 24 Jul 2008 12:04:19 GMT

Hi,

Please post here the output of "ioscan -fnCdisk" from both nodes.

Pedro

Re: cmquerycl not work

Deepak Kr — Sun, 27 Jul 2008 08:25:50 GMT

Hi,

Run ioscan -funC disk on both the nodes and see if required disks are available specially disk which are comming from storage box.

Also try running insf -e on node ncpbmte1 after running ioscan

No common disk should be in No_HW state.

Also, if possible create Vgs on first node node and try importing to ncpbmte1 and see the results.

Re: cmquerycl not work

gigiz — Tue, 05 Aug 2008 08:45:32 GMT

Hi,
i have already suspect a disk problem but the storage group anwer me no error.

Then all my check i tell at the storage-group to check careful the disk and they tell me that we have a bad link.