topic Re: I/O and dump in Operating System - HP-UX

I/O and dump

mark.M — Thu, 29 Sep 2005 20:40:04 GMT

rp3440
OS ll.00
what is this???

Main Menu: Enter command or menu > sea

Searching for potential boot device(s)
This may take several minutes.

To discontinue search, press any key (termination may not be immediate).

IODC
Path# Device Path (dec) Device Path (mnem) Device Type Rev
----- ----------------- ------------------ ----------- ----
P0 0/0/2/0.0 ide.0 Random access media 1

P1 0/1/1/0.1 intscsia.1 Random access media 1

P2 0/1/1/0.0 intscsia.0 Random access media 1

Main Menu: Enter command or menu > bo p0
Interact with IPL (Y, N, or Cancel)?> n

Booting...
Boot IO Dependent Code (IODC) revision 1

HARD Booted.

ISL Revision A.00.38 OCT 26, 1994

ISL booting hpux (;0):INSTALL

Boot
: disk(0/0/2/0.0.0.0.0.0.0;0):WINSTALL
8962064 + 1174208 + 1998104 start 0x278968

Firmware Version 45.11

Duplex Console IO Dependent Code (IODC) revision 1

Stored message buffer up to panic:

System Panic:

linkstamp: Thu Jul 19 11:39:34 MDT 2001
_release_version: @(#)B2352B/9245XB HP-UX (B.11.00) #1: Wed Nov 5 22:38:19 PS
T 1997
__kern_ci_revision: $Header: kern_sequence.c,v 1.6.106.512 97/11/05 18:01:46 mso
sa Exp $

panic: set_machine_parameters_64: Unidentified cpu type returned from PDC_MODEL

PC-Offset Stack Trace (read across, top of stack is 1st):
0x0037c8ac 0x004e8bc8 0x004e8a28
0x004e7040 0x0038bdfc 0x00278e9c
End Of Stack

*** A system crash has occurred. (See the above messages for details.)
*** The system is now preparing to dump physical memory to disk, for use
*** in debugging the crash.

ERROR: Your system crashed before I/O and dump configuration was complete.
A crash dump cannot be taken under these circumstances without
special configuration. Contact your HP support representative.

Re: I/O and dump

baiju_3 — Thu, 29 Sep 2005 20:48:35 GMT

Does this model support 11.0 ? I am not sure , see the link it says 11i v1 and v2.

http://www.hp.com/products1/servers/rackoptimized/rp3400_series/index.html

thx,
bl.

Re: I/O and dump

Adisuria Wangsadinata_1 — Thu, 29 Sep 2005 20:50:31 GMT

Hi,

To be frank with you, the answer of your question is : this is the error message when you try to install something on your system.

You need to check on the system log (SL) on your MP (Management Processor) :

1. from your console, press 'CTRL+B'
2. input the user/password
(Admin/Admin OR Oper/Oper)
3. type SL > E > T
4. check also the power status (PS) :
type CM > PS
5. check the LED status on your system
from MP prompt, type VFP

You can check the PIM information from BCH mode, goto INFO >PIMINFO

If you can describe more detail about the situation, it's very help to narrow down to the exact problem.

As stated on the message above, it's better you log a call also to HP.

Hope this information can help you.

Cheers,
AW

Re: I/O and dump

mark.M — Thu, 29 Sep 2005 20:59:27 GMT

thank you lalb
i'm slov....

Re: I/O and dump

Adisuria Wangsadinata_1 — Thu, 29 Sep 2005 21:02:52 GMT

Hi,

See the url below :

Supported system on HP-UX 11.i v1:
http://www.docs.hp.com/en/5990-7279/ch03s01.html

Supported system on HP-UX 11.00 :
http://www.docs.hp.com/en/5990-6721/ch01s08.html

RP3440 is for HP-UX 11.i NOT HP-UX 11.00.

So it's looks like you used wrong version to install RP3440 OR some problem on the hardware (for troubleshooting check previous reply from me).

Hope this information can help you.

Cheers,
AW

Re: I/O and dump

Arunvijai_4 — Thu, 29 Sep 2005 22:39:38 GMT

As per the specification, It will support only 11i v1 and 11iv2. Take a look this page,

http://www.hp.com/products1/servers/rackoptimized/rp3400_series/specifications.html

-Arun