topic Re: Shell Script in Operating System - HP-UX

Shell Script

Vasudevan MV — Tue, 28 May 2002 17:21:07 GMT

Hi,

Can any one tell me, is there any command to get the full hostname other than nslookup?. When I type "echo $DISPLAY", it gives "xyz:10.0", but I need to export the DISPLAY variable to xyz.tt.nt.com:10.0 (with the full hostname).

Thanks
Vasu

Re: Shell Script

Paula J Frazer-Campbell — Tue, 28 May 2002 17:30:56 GMT

Hi

Will hostname give you what you want?

Paula

Re: Shell Script

PIYUSH D. PATEL — Tue, 28 May 2002 17:34:39 GMT

Hi,

Apart from nslookup....

Use #hostname - that will give u the hostname
eg. node1

then use #domainname - that will give you the domain name
eg xyz.com

Hence use node1.xyz.com

HTH,
Piyush

Re: Shell Script

Peter Kloetgen — Tue, 28 May 2002 17:43:01 GMT

Hi Vasudevan,

you can put the full qualified domain name together with command substitution and a variable:

variable=`hostname``domainname`
(use backticks here everywhere to get it work)
echo $var

--> will deliver you the FQDN of that host

Allways stay on the bright side of life!

Peter

Re: Shell Script

Miguel Covas — Tue, 28 May 2002 17:54:32 GMT

It seems that nslookup is going to be replaced by host. But since there is no host command in HPUX I think that you have to stick to nslookup. nslookup will search DNS but you can configure it to search on /etc/hosts if you need that.

Otherwise is unlikely that you get a standard way to get the full qualified host name or address. My experience is that usually domainname gives you blank. Admin seldom care to initialize it properly and in these times of LDAP, yp is not so popular...

If you need to inform DISPLAY I think that combining hostname and nslookup will do the job. Otherwise you can inspect /etc/hosts, but you can end up looking up a mere 127.0.0.1 localhost.

Since there is no host command, my advice is
(sorry) nslookup

Re: Shell Script

Helen French — Tue, 28 May 2002 17:58:01 GMT

If the FQDN has been set at the last ( in the 3rd column), then this would display it:

# cat /etc/hosts | grep `hostname` | awk '{print $3}'

just a thought ..

Re: Shell Script

Christopher McCray_1 — Tue, 28 May 2002 18:38:08 GMT

Hello,

It won't give you the full output, but

# who -mT

should do the trick

Chris

Re: Shell Script

MANOJ SRIVASTAVA — Tue, 28 May 2002 18:45:35 GMT

Hi

hsotname is the command.

Manoj Srivastava

Re: Shell Script

Christopher McCray_1 — Tue, 28 May 2002 19:04:46 GMT

Hello again

Here is what I put into scripts for exporting displays:

export DISPLAY=`who -mT | awk '{print $9}'`:0.0

Hope this helps

Chris

Re: Shell Script

Bill Hassell — Tue, 28 May 2002 19:17:36 GMT

Whether you can see the domain name or not is very dependent on whether you use DNS, NIS or /etc/hosts for name resolution. A more general solution is to use the IP address (which takes care of everything):

DISPLAY=12.34.56.78:0.0

By setting the IP address, you are assured of zero problems with name resolution.

Re: Shell Script

Glenn L. Stewart — Wed, 29 May 2002 11:49:29 GMT

I agree with the above post. You can simply use the ip if you can't use nslookup.

Try the following as a slightly more robust solution.

HOST=$(hostname)
CURRENT_IP=$(getip $HOST)
export DISPLAY=$CURRENT_IP:0.0

Of course these can be combined into one line...

Curious: What can't you use DNS?

If DNS cannot be used, you may try placing host in question in the /etc/hosts, ensuring that files is before DNS in your nsswitch.conf

Glenn