topic Re: fbackup failure in Operating System - HP-UX

fbackup failure

Asad Malik — Thu, 22 Mar 2001 14:36:06 GMT

Hi
When we run a scheduled fbackup it gives these messages in syslog.
Mar 21 02:16:22 omrss1 vmunix:
Mar 21 02:16:22 omrss1 vmunix: SCSI: Unexpected Disconnect -- lbolt: 3294157, dev: cd015000, io_id: 1010f50
Mar 21 02:16:22 omrss1 vmunix: SCSI: ATN ignored -- lbolt: 3294159, dev: cd015000
Mar 21 02:16:22 omrss1 vmunix: lbp->state: 20
Mar 21 02:16:22 omrss1 vmunix: lbp->offset: ffffffff
Mar 21 02:16:22 omrss1 vmunix:
Mar 21 02:16:22 omrss1 vmunix: lbp->uPhysScript: b80000
Mar 21 02:16:22 omrss1 vmunix: From most recent interrupt:
Mar 21 02:16:22 omrss1 vmunix: ISTAT: 2a, SIST0: c0, SIST1: 00, DSTAT: 00, DSPS: 00b80500
Mar 21 02:16:22 omrss1 vmunix: lsp: 9a57600

for Mar 22

Mar 22 02:15:50 omrss1 ftpd[5822]: FTP session closed
Mar 22 02:16:33 omrss1 vmunix:
Mar 22 02:16:33 omrss1 vmunix: SCSI: Unexpected Disconnect -- lbolt: 11935209, dev: cd015000, io_id: 101c5d3
Mar 22 02:16:53 omrss1 cmcld: Warning: cmcld process was unable to run for the last 8 seconds,
Mar 22 02:16:53 omrss1 cmcld: which is longer than the node timeout (5 seconds)
Mar 22 02:16:53 omrss1 cmcld: Communication to node omrss2 has been interrupted
Mar 22 02:16:53 omrss1 cmcld: Node omrss2 may have died
Mar 22 02:16:53 omrss1 cmcld: Attempting to form a new cluster
Mar 22 02:16:56 omrss1 ftpd[5893]: gethostbyaddr: omrss1.omers.com. != 10.1.0.55
Mar 22 02:16:56 omrss1 cmcld: Resumed updating safety time
Mar 22 02:16:58 omrss1 cmcld: 2 nodes have formed a new cluster, sequence #7
Mar 22 02:16:58 omrss1 cmcld: The new active cluster membership is: omrss2(id=2), omrss1(id=1)

When we do an interactive backup it works and no error messages.
HP hs already replaced tape drive and cable

Any suggestions

Thanks

Re: fbackup failure

Paula J Frazer-Campbell — Thu, 22 Mar 2001 15:10:20 GMT

Hi
You have a scsi device problem being reported, is the device in syslog your backup device (DAT/DLT)?

I would guess that the backup is failing because the target device is not behaving correctly.

Check all cables/cards and retry backup - if it again fails log a HP support call for the faulty device.

HTH

Paula

Re: fbackup failure

Paula J Frazer-Campbell — Thu, 22 Mar 2001 15:19:01 GMT

Hi
Further info:-
Your
Mar 21 02:16:22 omrss1 vmunix: SCSI: ATN ignored -- lbolt: 3294159, dev: cd015000

Indicates an EMC error

Paula

Re: fbackup failure

Asad Malik — Thu, 22 Mar 2001 16:35:43 GMT

yes the device is tape drive.

Re: fbackup failure

Dan Zucker — Sun, 25 Mar 2001 06:53:15 GMT

A few of questions.

1) Have you tried using schedule to run at 22:00?
2) The messages are from 2:16, at what time does the backup begin and how much time does it need when run interactivly?
3) Have you been on-site when the backup runs?

Dan