topic Re: Errors after patch upgrade in Operating System - HP-UX

Errors after patch upgrade

Anil C. Sedha — Fri, 20 Dec 2002 20:12:43 GMT

Hi,

I installed my latest fourth quarter patch bundle. After that we are facing problems in compilation and accessing system resources as the environment does not work well sometimes. sys.resources got changed and stuff.

Can someone pls guide me if i can rollback this patch bundle. This patch bundle is internal to our organization. It comes to us as a script which has all patch names and then a swinstall command in the command which get's it for us from the depot.

Good answers will be rewarded.

Regards,
Anil

Re: Errors after patch upgrade

Khalid A. Al-Tayaran — Sun, 22 Dec 2002 05:01:15 GMT

Hi,

I did not try this:

Look at swremove

for example:

B.11.00.20.09 HPUX 11.0 Support Tools Bundle, Mar 2002
B.11.00.56.5 Quality Pack for HP-UX 11.00, March 2002
B.11.00.0203. Hardware Enablement Patches for HP-UX 11.00, March 2002

Note: Quality Pack and Hardware Enablement Patches must be installed/removed together.

Again, I did not try this, if someone has comments or notes for us beginners please let us know.

Good luck.

Re: Errors after patch upgrade

eran maor — Sun, 22 Dec 2002 15:32:03 GMT

Hi

i dont know for a easy way for rollback of installing a bundles of patches .

the only way that you can try it to check what new patches you install with the new bundle of support plus patches and try to remove them .

i will not recommend to do this !

the easy way is just to restore the system from a make_tape_recovery tape , i hopw that you have this tape .

also , i dont know about big issue that there is with the support plus bundles , i m installing it all the time ( like you ) every 3 month but i dont have a lot of applic.

if you dont have a clue what is the problem with your system and you have a lot of problem with compile i can guess that it is about :
libc , ld and linker patches that is causeing you problem but you didnt gave us any error to try to solve it .

you can also check the status of the install of the patches with the command :
swlist -l fileset -a state | grep -i install
swlist -l fileset -a state | grep -i currapt

if you have fileset that is in this state you need to fic this problem .

remember that you need to check it on only install patches , not all the patches .

you can get all the install patches with the command :
show_patches

and you can also run the until . check_patches to see if you have problem with your patches .

Re: Errors after patch upgrade

Jim Butler — Mon, 23 Dec 2002 14:24:41 GMT

I have seen this.

Try getting a good version of the SWDIST patch (phco_25875 -
works for me.)

Install that

Then go back and reinstall the bundle you just tried

You can look to see if your patches match what is in the kernel -
10 bucks says that is what your problem is.

Re: Errors after patch upgrade

SSP_1 — Thu, 16 Jan 2003 06:12:14 GMT

Hi Anil ,

It's long time man ..no mail ..no contact. It seems U R quite busy and learning a lot on hp-ux. GR* pitching in man...I used to read your posts.

Reply me on my mail id
"shripad.patkar@seepz.tcs.co.in" whenever U have time.

regards
Shripad

Re: Errors after patch upgrade

Ravi_8 — Thu, 16 Jan 2003 06:29:28 GMT

Hi, Anil

did u installed H/W enable patches?

QPK and HWE patche bundles go together

Re: Errors after patch upgrade

RAC_1 — Thu, 16 Jan 2003 06:35:14 GMT

hope you have ignite recovery backup prior to patch installation.

Also check for corrupt patches-

swlist -l patch -a state

check for corrupt.

Also if I remember correctly QPK and HWE should go toghther, it seems that you applied only QPK.

Re: Errors after patch upgrade

SSP_1 — Thu, 16 Jan 2003 07:07:53 GMT

Hi Anil Seddha ,

What I can suggest you is to get the product name/no. for your hardware enablement/QPK patches, try a simple syntax "swlist -l fileset -a state ". eg. swlist -l fileset -a state XSW800GR1020 . Back out all the filesets which shows the ambigious state of corr/unconfig.

Re: Errors after patch upgrade

Trond Haugen — Thu, 16 Jan 2003 07:53:25 GMT

You didn't say if the patchinstallation was checked to be OK. Check the swagent.log. Also the suggested checking for fileset stat will help some. As a roule I will recomend checking the state also BEFORE installing patches. That way you will know if any problems was present befor the installation.
Did you instll the patches using "Manage Patch Selection"? I have seen problems when patches has been selected "manually" and don't realy match installed products. If there is a missmatch you should be able to recover by swremoving.

Regards,
Tron