topic Re: Problems installing 11i on V2500 in Operating System - HP-UX

Problems installing 11i on V2500

Chris Fadrowski — Fri, 13 Dec 2002 21:33:43 GMT

I need some help. I have been trying to cold install 11i on a v2500 running 11.0. Well, it looks as if everything installs fine, reboots and it asks me to network the server. I go thru this just fine and it reboots. At this point on the reboot it hangs at

start syncer daemon

and it just hangs. Can't do anything else at this point. I have to take the system down hard to get out of it. I tryed to boot into single user mode but i get an error from EXEC that says file or directory can't be found. any ideas? I have tryed the June 2002 CD's and the Sept 2002 cds.

Re: Problems installing 11i on V2500

erics_1 — Fri, 13 Dec 2002 21:43:18 GMT

Chris,

You may want to hit the key combo of | (pipe symbol) to break out of the startup script. You can then check your logs for what may be causing the problem.

Hope this helps!
Eric

Re: Problems installing 11i on V2500

Ian_4 — Sat, 14 Dec 2002 17:44:11 GMT

V2500 based on PA-8200 and newer CPUs running in 64-bit mode are supported with 11i - R U running 64 or 32 bit?

Hope this helps.

Re: Problems installing 11i on V2500

Chris Fadrowski — Mon, 16 Dec 2002 13:48:14 GMT

Control Shift | doesn't work to get out of that. I tried that several times.

I am trying to install the 64 bit 11i OS.

Re: Problems installing 11i on V2500

harry d brown jr — Mon, 16 Dec 2002 16:05:43 GMT

Is it booting from the correct disk path? Have you tried to boot into single user?

also see this http://forums.itrc.hp.com/cm/QuestionAnswer/1,,0x022718276953d61190040090279cd0f9,00.html

and found here:
http://forums.itrc.hp.com/cm/TopSolutions/1,,CA463824!1!questions,00.html

live free or die
harry

Re: Problems installing 11i on V2500

Patrick Wessel — Mon, 16 Dec 2002 16:09:20 GMT

Chris,
Which Teststation Software is installed on your system? You need alt least 3.2 to install hp-ux 11i
You can verify the version using the following command as sppuser on the teststation: diag_version

Re: Problems installing 11i on V2500

Chris Fadrowski — Mon, 16 Dec 2002 16:11:09 GMT

i can't boot into single user mode. when i try ISL doesn't work with a message of file or directory not found.

11.0 works okay on this system. Does this have to do with firmware? HP told me i didn't have to be concerned with firmware on this box like you do on an N class and told me everything should be fine. But it makes me wonder.

Re: Problems installing 11i on V2500

Chris Fadrowski — Mon, 16 Dec 2002 16:13:06 GMT

Patrick, you may be on to something, however, i just connected my V to a console port and am NOT using the the control station at this point. It is OFF in fact. Just using the console port to a green screen (amber) monitor that all my HPUX servers are attached to .

Re: Problems installing 11i on V2500

Christopher McCray_1 — Mon, 16 Dec 2002 16:16:12 GMT

Hello,

After interrupting the autoboot, are you typing:

boot pri ipl hpux -is

you have to specify ipl, otherwise the system will proceed with the boot without asking you if you want to interact with the ISL.

If this doesn't work (for whatever reason), please post the output.

Hope this helps

Chris

Re: Problems installing 11i on V2500

Chris Fadrowski — Mon, 16 Dec 2002 16:21:19 GMT

i stop the boot up sequence and type

bo pri isl

and it comes back with

error: can't execute
Can't find file or directory

AT THIS POINT, if i boot
the system normally, it
hangs on

start syncer daemon

Doesn't go any further
than that.

But it does run 11.0

Re: Problems installing 11i on V2500

Christopher McCray_1 — Mon, 16 Dec 2002 16:24:09 GMT

Hello,

As i said,

don't type

boot pri isl

type

boot pri ipl

What does it say?

Chris

Re: Problems installing 11i on V2500

Patrick Wessel — Tue, 17 Dec 2002 08:27:54 GMT

Chris,
That makes it a little bit harder to verify if the firmware level of your box is suitable to 11i but not impossible. But it is impossible to upgrade the firmware if it doesn???t fit. You cannot do this without the Teststation
You receive the firmware versions after the system past the power on self test (post) it starts with ???PDC Firmware Version Information??? could you please post the versions of:
PDC_ENTRY
POST
OBP
SPP_PDC

Re: Problems installing 11i on V2500

Chris Fadrowski — Tue, 17 Dec 2002 16:58:40 GMT

PDC 3.1
PDC Entry is 4.3

running diag_version outputs 3.1 on the workstation

Re: Problems installing 11i on V2500

Patrick Wessel — Wed, 18 Dec 2002 16:33:22 GMT

Chris,
I???m afraid that I the firmware version suits. It???s not the current one (3.2) but it should work
There is a way to bring a V-Class server to ISL, but it???s useless. To boot to single user mode you need to enter the following string at the Boot Console Handler (Command prompt)
bo ???is
(fare to easy, isn???t it?)

The V-Class was originally designed by Convex running spp-ux and not hp-ux. Due to that are the firmware layer and the OS-loader different.

Re: Problems installing 11i on V2500

Chris Fadrowski — Wed, 18 Dec 2002 16:55:15 GMT

i seem to have 2 separate issues

1. i can't load 11i. Install goes fine until boot up and it hangs on "start syncer daemon" Could this have something to do with the cd's trying to install ISL? This is with the v connected directly to a console

2. When i connect the workstation to the v (instead of the console) i can't get into the v from the upper most screen. It doesn't give me a prompt.

I am pretty lost by this point
and would think that if it were firmware issues i would get errors on install stating so.

Re: Problems installing 11i on V2500

Steven E. Protter — Wed, 18 Dec 2002 17:22:47 GMT

The V class is certified for 11i right? I think so.

If you are trying the upgrade, I'd forget it, I went through that in class and would never do it in real life.

If your're not doing it, do a cold install.

At the console you should be able to bypass the error as instructed above.

Someone here might be able to help, but this sounds like a backline support call to me.

Steve