topic Re: Linux bonding fails in Operating System - Linux

Linux bonding fails

Aaron Carr — Mon, 28 Jun 2004 12:21:42 GMT

I'm attempting to configure bonding on an HP Proliant DL380G3 running Red Hat Enterprise Linux 2.1 update 4.

I configure bond0 as follows:

DEVICE=bond0
BOOTPROTO=none
ONBOOT=yes
IPADDR=10.1.57.111
NETWORK=10.1.57.0
USERCTL=no
NETMASK=255.255.252.0

I configure eth0:

DEVICE=eth0
BOOTPROTO=none
ONBOOT=yes
MASTER=bond0
SLAVE=yes
USERCTL=no

I configure eth1:

DEVICE=eth1
BOOTPROTO=none
ONBOOT=yes
MASTER=bond0
SLAVE=yes
USERCTL=no

This is my modules.conf:

alias parport_lowlevel parport_pc
alias eth0 bcm5700
alias eth1 bcm5700
options bcm5700 line_speed=100,100 auto_speed=0,0 full_duplex=1,1
alias bond0 bonding
probeall bond0 eth0 eth1 bonding
options bond0 mode=1 miimon=100 primary=eth0
alias scsi_hostadapter cciss
alias scsi_hostadapter1 cciss_2445
alias scsi_hostadapter2 cciss_2445
alias usb-controller usb-ohci

Once this is done, I attempt to restart the network for bonding to take effect, but I get the following error:

bonding_init(): either miimon or arp_interval and arp_ip_target module parameters must be specified, otherwise bonding will not work - see bonding.txt for details. Bonding driver not loaded.

Any help here would be greatly appreciated.

Re: Linux bonding fails

Vitaly Karasik_1 — Tue, 29 Jun 2004 01:48:32 GMT

Aaron,

Try to start bonding without "mode=1 miimon=100 primary=eth0" parameters - I don't sure if bcm5700 support MII.

BTW, this may be relevant : http://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=112926

Rgds,
Vitaly

Re: Linux bonding fails

Aaron Carr — Tue, 29 Jun 2004 08:02:20 GMT

I tried removing miimon=100 primary=eth0 as you suggested, but still no luck.

Also, I don't think this relates to the bug you pointed out, because the bonding driver does not load at all.

I also get "Bringing up interface bond0: bonding device does not seem to be present, delaying bond0 initialization." and sometimes it says "bond0 not an ethernet like device".

If there's any more info I can supply, let me know and I'll dig it up.

Re: Linux bonding fails

Vitaly Karasik_1 — Tue, 29 Jun 2004 10:55:48 GMT

you're right, this bug doesn't related to your problem.

If I understand properly, bonding module isn't loaded . did you try "insmod bonding" from commmand line?

Re: Linux bonding fails

ginnie nuckles_1 — Fri, 16 Jul 2004 13:55:13 GMT

I have not seen a post to this that stats the resolution ??? I am tearing my hair out on this one .. did you find a solution please ?? thanks

Re: Linux bonding fails

Vitaly Karasik_1 — Sun, 18 Jul 2004 00:26:57 GMT

Ginnie,
Do you have exactly the same problem?

Re: Linux bonding fails

ginnie nuckles_1 — Sun, 18 Jul 2004 13:38:45 GMT

yes

Re: Linux bonding fails

Vitaly Karasik_1 — Mon, 19 Jul 2004 01:04:31 GMT

can you check in "lsmod" output if bonding module is running? and if no, try "insmod bonding".

Re: Linux bonding fails

Aaron Carr — Mon, 19 Jul 2004 08:13:51 GMT

My solution was to ditch 2.1 AS and move to RHEL 3 (once the Proliant Support Pack was updated to v 7.1).

I tried the insmod bonding, as mentioned earlier, but that didn't help.

Re: Linux bonding fails

Matti_Kurkela — Thu, 22 Jul 2004 04:26:10 GMT

> I tried the insmod bonding, as mentioned earlier, but that didn't help.

For future reference:
It seems that the bonding module didn't load.
When you're having module problems, the error messages of insmod/modprobe commands may not be very informative. More information can usually be found in the kernel message buffer. You can check it with the "dmesg" command.