topic Re: network card speed/mode settings in Operating System - Linux

network card speed/mode settings

Matthias Bayer — Thu, 04 Jan 2001 10:35:13 GMT

Hi,

can anyone tell me how to find out which speed and which mode (10 HD / 100 FD) the network card is using and how to set e.g. the card fix to 100 FD ?

thanks

Re: network card speed/mode settings

Alexander M. Ermes — Thu, 04 Jan 2001 13:44:33 GMT

Hi there.
One question : Which chipset on the lan interface ?
For certain chipsets there maybe some tools.
In general :
Try to transfer data from another computer with
the midnight commander. That will show you the
data transfer rate. If the rate is larger 1.25 MB, the speed is 100 MBit.
Rgds
Alexander M. Ermes

Re: network card speed/mode settings

Dan Wanek — Mon, 08 Jan 2001 16:24:23 GMT

Check out the mii-diag util. The source can be dowloaded from ftp://ftp.scyld.com/pub/diag/mii-diag.c

Re: network card speed/mode settings

Marco Paganini — Mon, 08 Jan 2001 22:12:58 GMT

That depends basically on the driver you're using. You should be able to get some information by looking at /var/log/messages. Look for the "eth0" string (supposing this is your first ethernet). It should show you the current speed.

Re: network card speed/mode settings

Andreas Kromat — Wed, 10 Jan 2001 11:36:03 GMT

We have the following entry in the /etc/conf.modules (Siemens Primergy-Server with Intel EEPRO100 and RH6.1)

alias eth0 eepro100
options eepro100 options=0x30

Re: network card speed/mode settings

Ovidiu D. Raita — Wed, 10 Jan 2001 19:32:57 GMT

Try
#lanadmin
then -> lan -> display

My output looks like this:

PPA Number = 0
Description = lan0 Hewlett-Packard 10/100 TX Half-Duplex TT = 1500
Type (value) = ethernet-csmacd(6)
MTU Size = 1500
Speed = 100000000
Station Address = 0x108327e7b5
Administration Status (value) = up(1)
Operation Status (value) = down(2)
Last Change = 1647
Inbound Octets = 0
Inbound Unicast Packets = 0
Inbound Non-Unicast Packets = 0
Inbound Discards = 0
Inbound Errors = 0
Inbound Unknown Protocols = 0
Outbound Octets = 410
Outbound Unicast Packets = 10
Outbound Non-Unicast Packets = 0
Outbound Discards = 0
Outbound Errors = 0
Outbound Queue Length = 0
Specific = 655367

Ovidiu

Re: network card speed/mode settings

Ovidiu D. Raita — Wed, 10 Jan 2001 19:44:31 GMT

I guess I was connected to the wrong Forum. lanadmin works for HP-UX. Just discard my former message.
.....
At least you know how to find this info on HP-UX systems :-)

Ovidiu

Re: network card speed/mode settings

Ashish Palkhiwala — Fri, 02 Feb 2001 16:58:28 GMT

I am assuming that you have 10/100 HP NIC in your system.

If so the simple way of doing this will be, Go to
/etc/rc.config.d/hpbase100conf .

You can hard code the value as 10HD or 100FD etc...
vi this file and within this file you should be able to set the speed and duplex mode as you wish provided that the card is smart enough to detect that.

Re: network card speed/mode settings

Lee Martin_1 — Wed, 22 Aug 2001 05:56:57 GMT

Hi,

well this answer may well be far too late, for the original question in Jan/Feb. Hopefully will be useful for oter though.

Assuming we are using the eepro100 driver you need to make the following entries in /etc/modules.conf

alias eth0 eepro100
options eepro100 options=0x30

The various options are:
Hex Decimal Meaning
0x10 16 Force Full-Duplex operation (must be used with 0x20 or 0x40)
0x20 32 Force 100mbps-only operation
0x30 48 Force 100mbps-only with Full Duplex
0x40 64 Force 10mbps-only
0x50 80 Force 10mpps-only with Full Duplex

It is possible to give options for more than one LAN card by comma separeting the options.

How to find out current speed:

linux1:~ # mii-diag eth1
Basic registers of MII PHY #1: 2100 780d 02a8 0154 05e1 0081 0000 0000.
Basic mode control register 0x2100: Auto-negotiation disabled, with
Speed fixed at 100 mbps, full-duplex.
You have link beat, and everything is working OK.
Your link partner is generating 100baseTx link beat (no autonegotiation).

Here you need to have installed the mii-diag of course :)

All this worked fine for me on SuSE 7.0.

Hope this helps.

Lee