https://community.hpe.com/t5/disk-enclosures/about-va7400-secure-mode/m-p/4379377#M30619 The array goes into secure mode if you<BR /><BR />a) configure this<BR /><BR />b) a battery goes below a certain level (failing battery)<BR /><BR />...<BR />Set Resiliency Level. This option sets the level of protection offered by data <BR />resiliency. It determines how often the contents of the controller maps are <BR />copied to the disk. Keeping the map information on the disks protects <BR />against controller map loss.<BR />SingleController is used if the array is operating with only one controller. <BR />This suppresses the single controller warning messages that are normally <BR />generated when only one controller is operating.<BR />Secure continually updates the disks at regular intervals. This option offers <BR />both data protection and good performance.<BR />Normal is the standard resilient map processing. This results in higher <BR />performance than Secure, but the risk of map loss is less than the <BR />HighPerformance configuration.<BR />RestrictedNormal has higher performance than Secure, but less than <BR />Normal, but the risk of map loss is less than the HighPerformance and <BR />Normal configuration.<BR />HighPerformance updates the disk maps only during shutdown of the <BR />array. This is the lowest level of data protection, but it offers the highest <BR />level of performance. Sun, 15 Mar 2009 15:36:20 GMT Torsten. 2009-03-15T15:36:20Z https://community.hpe.com/t5/disk-enclosures/about-va7400-secure-mode/m-p/4379376#M30618 hello:<BR /><BR />1) when Va7400 battery in a controller is installed into VA disk array, the battery will discharge and then charge, is it true ?<BR />2) when the battery discharges, the disk array will change to secure mode, which means the RAM will be stopped. this conception is true ?<BR /><BR />3) and then , with what condition about battery VA7400 will change to secure mode?<BR /><BR />4) I now use another VA7400, when a controller is installd into it, the rmain capacity is 38%, but the disk array does not goto secure mode, why ?<BR /> Sun, 15 Mar 2009 03:57:57 GMT https://community.hpe.com/t5/disk-enclosures/about-va7400-secure-mode/m-p/4379376#M30618 johnson_luo 2009-03-15T03:57:57Z https://community.hpe.com/t5/disk-enclosures/about-va7400-secure-mode/m-p/4379377#M30619 The array goes into secure mode if you<BR /><BR />a) configure this<BR /><BR />b) a battery goes below a certain level (failing battery)<BR /><BR />...<BR />Set Resiliency Level. This option sets the level of protection offered by data <BR />resiliency. It determines how often the contents of the controller maps are <BR />copied to the disk. Keeping the map information on the disks protects <BR />against controller map loss.<BR />SingleController is used if the array is operating with only one controller. <BR />This suppresses the single controller warning messages that are normally <BR />generated when only one controller is operating.<BR />Secure continually updates the disks at regular intervals. This option offers <BR />both data protection and good performance.<BR />Normal is the standard resilient map processing. This results in higher <BR />performance than Secure, but the risk of map loss is less than the <BR />HighPerformance configuration.<BR />RestrictedNormal has higher performance than Secure, but less than <BR />Normal, but the risk of map loss is less than the HighPerformance and <BR />Normal configuration.<BR />HighPerformance updates the disk maps only during shutdown of the <BR />array. This is the lowest level of data protection, but it offers the highest <BR />level of performance. Sun, 15 Mar 2009 15:36:20 GMT https://community.hpe.com/t5/disk-enclosures/about-va7400-secure-mode/m-p/4379377#M30619 Torsten. 2009-03-15T15:36:20Z https://community.hpe.com/t5/disk-enclosures/about-va7400-secure-mode/m-p/4379378#M30620 hello:<BR /><BR />what is the battery evaluation standard?<BR /><BR />what is the failed battery ? <BR />what is the good status of battery ?<BR /><BR />I see a battery's remain capacity is 84%, and the battery Light is lighting green But a battery with 91% capacity is <BR />flinking. <BR /><BR />why ?<BR /> Tue, 17 Mar 2009 01:40:41 GMT https://community.hpe.com/t5/disk-enclosures/about-va7400-secure-mode/m-p/4379378#M30620 johnson_luo 2009-03-17T01:40:41Z