topic Re: connecting 2 VA7410 in HPE EVA Storage

connecting 2 VA7410

Francois_6 — Sat, 05 Jul 2003 06:36:39 GMT

Hello guys,
i have the following problem; i have 2 different sites A and B having each several servers connected to different VA7410 through fibre switches. i'm trying to connect these 2 sites to each others cause we want that servers in site A could see the VA in site B and vice versa. When connecting switches the servers do not see the VAs no more, the armdiscover could no more detect any VA even in the same site ( servers in site A could no more see VA in site A or B, and vice versa )
Please advise..
Francois

Re: connecting 2 VA7410

Eugeny Brychkov — Sat, 05 Jul 2003 18:25:48 GMT

Francois,
most possibly you have zoning enabled on both switches (or on one of two switches) and switches are having problems syncronizing zoning between them. You should build one SAME for both switches zoning table, download it to BOTH switches, enable them and only THEN you can connect switches with ISL.
If you do errshow at switches you may see 'fabric segmented' events logged. This events is about switches are not able to sync their zoning
Eugeny

Re: connecting 2 VA7410

Vincent Fleming — Sun, 06 Jul 2003 10:27:13 GMT

It sounds like you have the Domain numbers all set to the same number... very common when the switches are not ISL'ed to other switches.

Check the Domain number for each of the switches - they should all be different.

Good luck,

Vince

Re: connecting 2 VA7410

Francois_6 — Tue, 12 Aug 2003 05:04:16 GMT

Hi guys,
i checked on the switches, it's ok. The main issue is when i connect the between sites switches. The VAs stop responding and are in a hang state. I need to cut power abnormally to reset them. I doubted the loop ID on the controllers. Could anybody help..!!
thank u

Re: connecting 2 VA7410

Eugeny Brychkov — Tue, 12 Aug 2003 05:35:36 GMT

Do you have Proliant servers in the SAN? With KGPSA or emulex FC cards? If yes, then please post here regisrty from hkey-local-machine\system\currentcontrolset\services\...\Parameters\Device
where ... is 'CPQKGPSA' for CPQ driver or 'lp..' for emulex. Needed variable is 'DriverParameter'
Eugeny

Re: connecting 2 VA7410

Francois_6 — Tue, 12 Aug 2003 11:34:38 GMT

Hi Eugeny,
the servers in the site are proliant servers with emulex LP950 FC cards. remark there is a tape library compaq msl5060 connected on one switch in site B. now the status is the following. i disconnected the switches between sites connections. each site rediscovered its VA. but in site B having the tape library, i still have problems with fiber so i put the tape library on one switch and the one va controller on the other and disconnect the 2nd controller so it worked. But when reconnecting the 2nd va controller to the same switch with tape library or when re-connecting between sites switches the problem re-occurs. the VAs disappears and couldn't be discovered.
Thanks

Re: connecting 2 VA7410

Eugeny Brychkov — Tue, 12 Aug 2003 19:47:26 GMT

Try the following:
1. upgrade VAs firmwares to A100;
2. upgrade card drivers. Please note that if you have compaq FCA cards (not native emulex) then CPQ driver called CPQKGPSA should be installed;
3. Try playing with driver settings (in registry) like ResetTPRLO set to 2, EmulexOption set to 0x3A00.
Good luck!
Eugeny

Re: connecting 2 VA7410

Francois_6 — Wed, 13 Aug 2003 11:29:42 GMT

Hello,
U're right the driver is CPQKGPSA. Attached hereby the entry in registry concerning the Driver Parameter.
Where to find the new firmware to download.
thanks again.

Re: connecting 2 VA7410

Eugeny Brychkov — Wed, 13 Aug 2003 12:43:34 GMT

It's not readable. Please zip and attach again. Use regedt32
Eugeny

Re: connecting 2 VA7410

Francois_6 — Mon, 18 Aug 2003 07:51:37 GMT

Hello,

The entry in the registry is:

Windows Registry Editor Version 5.00

[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\CPQKGPSA\Parameters\Device]
"DriverParameter"="CrfIntrpt=0x1; CrfMsCnt=0x1; CrfRspCnt=0x8; ElsRetryCount=0x6; EmulexOption=0xAA00; EnableDPC=0x1; ErrRetryMax=0x0; NodeTimeOut=0x3C; ResetTPRLO=0x1; SimulateDevice=0x1; Topology=0x1; "
"MaximumSGList"=dword:00000021
"NumberOfRequests"=dword:00000032

The VA controller firmware is A000. Where can i find the A100 firmware to make the upgrade ?

Regards...

Re: connecting 2 VA7410

Eugeny Brychkov — Mon, 18 Aug 2003 19:43:22 GMT

To upgrade to A100 you need to call HP. Only HP CE or other certified person is allowed to do it.
Please upgrade your drivers to 4.82a14 (available from HP site, use CPQKGPSA for CPQ emulex cards), then check that there're no spaces in the registy parameters string, and then modify:
ResetTRLO=2
EmulexOption=0xBA00
Eugeny

Re: connecting 2 VA7410

Eugeny Brychkov — Mon, 18 Aug 2003 19:45:07 GMT

Sorry typo in my previous post, it should be
ResetTPRLO=2
Eugeny

Re: connecting 2 VA7410

Adam White_1 — Tue, 13 Apr 2004 21:37:56 GMT

Hi Eugeny

What does setting these two parameters do?

Thanks

Adam