topic Re: MSL5026 problem in HPE EVA Storage

MSL5026 problem

easynet — Mon, 02 Nov 2009 12:29:14 GMT

Hi, I have a problem with a driver of a MSL5026. This the message i see: did not match serial number xxxxxxxx provided by Compaq StorageWorks DLT/SDLT Minium (Changer0) among the list of drivers.
Someone knows gives some information to me?

Thanks

Re: MSL5026 problem

Torsten. — Mon, 02 Nov 2009 13:15:37 GMT

Where did you get this message?

Re: MSL5026 problem

easynet — Mon, 02 Nov 2009 14:16:00 GMT

On the eventviewer from the server, which the storage is connected

Re: MSL5026 problem

Torsten. — Mon, 02 Nov 2009 14:21:24 GMT

Who complains? The backup application?

Re: MSL5026 problem

easynet — Mon, 02 Nov 2009 16:54:24 GMT

i wonna use NTBACKUP on W2003 server.
if ai connet in SCSI the LTO to the server, it see two DLT and a Changer. but if i connet it in Fiber Channel, the server mount 1 DLT and a Changer, and in the event viewer i see that error

Re: MSL5026 problem

Torsten. — Tue, 03 Nov 2009 10:34:45 GMT

The information flows bit by bit into this thread ...

You should check the NSR discovery and mapping page now.

Re: MSL5026 problem

NXS — Tue, 03 Nov 2009 11:22:25 GMT

The barcode reader has a problem

Re: MSL5026 problem

Torsten. — Tue, 03 Nov 2009 11:28:38 GMT

The barcode reader will make a drive invisible? Why?

Re: MSL5026 problem

easynet — Tue, 03 Nov 2009 15:24:03 GMT

if The barcode reader has a problem, why it works fine in SCSI e not in FC ?

Re: MSL5026 problem

Torsten. — Tue, 03 Nov 2009 15:31:26 GMT

Did you check the NSR already? Any results?

Re: MSL5026 problem

easynet — Tue, 03 Nov 2009 16:09:34 GMT

excuse me, how can i check the nsr mapping ? is there a web interface on the FCtoSCSI router? ora by serial cable ? may i know the right commands to show the mapping ?

Re: MSL5026 problem

Uwe Zessin — Tue, 03 Nov 2009 16:17:10 GMT

Yes, there are a Web and a Telnet interface and with the special cable you can also make a serial connection (but do not confuse the MSL cable with the NSR cable).

Re: MSL5026 problem

easynet — Thu, 05 Nov 2009 11:57:35 GMT

i plugged the eth in the switch. the leds is green. but the switch not listen any mac.
swt-002-esn#sh mac-address-table interface f0/17
Mac Address Table
-------------------------------------------

Vlan Mac Address Type Ports
---- ----------- -------- -----

the guide tell this :
Default Ethernet settings
The basic factory default values are:
IP address: http://1.1.1.1/
Subnet mask: 255.255.255.0
Gateway address: 0.0.0.0
User name: root
Password: password

but pinging it, no responce.
i tried to reset the FC device too but maybe because it is refurbished, the ip was changed

Re: MSL5026 problem

Torsten. — Thu, 05 Nov 2009 13:36:40 GMT

Newer NSR model and newer firmware has a default IP setting of DHCP!

To change this, you need a serial connection.

Re: MSL5026 problem

easynet — Thu, 05 Nov 2009 16:26:47 GMT

it is possible, but why from switch i dont see any mac-address from f0/17 where plugged the cable ? if the device asks for DHCP ip i'll see the mac in the show mac-address output!

Re: MSL5026 problem

Torsten. — Thu, 05 Nov 2009 17:08:44 GMT

Power cycle the box to ensure it is not hung. Connect to serial port and see what it does.

Re: MSL5026 problem

easynet — Thu, 05 Nov 2009 17:39:23 GMT

the serial cable have a part number ? to order it

Re: MSL5026 problem

Torsten. — Thu, 05 Nov 2009 17:41:54 GMT

Should be delivered with the box. Caution - there are 2 different cables (for library and NSR), they look similar, but are different!

Re: MSL5026 problem

easynet — Thu, 05 Nov 2009 18:14:56 GMT

i bought a used device, no cable. how can i buy the right one ?