topic Re: Update BIOS, Netserver LC3 in Netservers

Update BIOS, Netserver LC3

Jonas_5 — Wed, 13 Mar 2002 08:23:51 GMT

I'm trying to update from NT4 to 2000 Server, and I believe that the BIOS is to old. (Update from BIOS version 4.06.23 to 4.06.38.)

First of all, I've have problems during POST (theese problems have not caused trouble as fare as I know):

0081-51 NetServer Management Controller SelfTest Failure
0090-64 DIMM Management Failure (sometimes)

But when I boot with the BIOS diskette (created from LC3BIOS_US.EXE), I get "Error. sdredit.exe failed."

After reading messages/articles, I tried to boot from a DOS diskette and then switched to the BIOS diskette, and ran the command:
A:> FLASHMMC LC3RA_US.BIN

In the beginning it's allright, but after a while I can see a warning,
"...cannot perform save/restore for MMC data because device is stuck in boot mode", after that I get
"Error: firmware update failure 0x3FE" and then the update is terminated.

I also have tried to unplugg the server for 2 minutes.

When I boot with a SF3 FLASH diskette (created from SF3FLASH.EXE), it says "Firmware update utility A.10.11" and that the download may take 5-10 min, but then "Failure IMPI Code 0xC1".

----------------------------------------------------------
HP NetServer LC3

CPU - PII 400 MHz

Phoenix BIOS 4.06.23 PQ
Adaptec SCSI BIOS v1.34S1

NetServer Management Controll Firmware version A.01.09
NetServer Management Controll Status C684
----------------------------------------------------------

Best regards
Jonas (...very much a beginner)

Re: Update BIOS, Netserver LC3

Marino Meloni_1 — Wed, 13 Mar 2002 08:54:27 GMT

hi
may be you already try this, but in case ...

when you have disconected the power of the server for two minuts, did you have also removed any conections like Lan, Modems Printers Ups ....?
some time the power bring by the pull up on the cable keep the memoy of MMC up and didn't clear.
if you have already done , discart this message

bye

marino

Re: Update BIOS, Netserver LC3

Jonas_5 — Wed, 13 Mar 2002 10:54:39 GMT

Thanks Marino, but I've tried it without success.

Adding info about the Firmware Update error
*********************************************
NetServer LC3 MMC Firmware Update Utility A.05.03
Copyright (c) 1997-1998 Hewlett-Packard
Flash file download revision A.05.03 HP MMC Feb 26 2002 14:46:41
boot revision A.03.02 BOOT MMC 09/12/98 16:28 52
Device current boot revision A.01.09
Warning: Cannot perform save/restore for MMC data
because device is stuck in boot mode
Setting up device for firmware download.
Device current boot revison A.01.09
Updating Firmware, Please Wait
< >
Error: Firmware update failure 0x3FF.
Firmware corrupted on MMC device.
********************************************

/J.

Re: Update BIOS, Netserver LC3

Marino Meloni_1 — Wed, 13 Mar 2002 11:08:47 GMT

hi
here you can found somes info, I haven't tryed myself but may be the solution

http://forums.itrc.hp.com/cm/QuestionAnswer/1,11866,0x4903c7af36b7d5118ff10090279cd0f9,00.html

http://forums.itrc.hp.com/cm/QuestionAnswer/1,,0x7bcf35067c18d6118ff40090279cd0f9,00.html

marino

Re: Update BIOS, Netserver LC3

Marco Hogeveen — Wed, 13 Mar 2002 11:12:03 GMT

Jonas,

A BIOS update from .23 to .38 is quite a big step.
If you have the possibility to update to an older version first, (from an old navigator CD?between .23 and .38) you might be lucky.

Otherwise, it looks like you have a hardware problem, the IO riser board would be most suspected (this is the board with the PCI slots and SCSI connectors).

Marco.

Re: Update BIOS, Netserver LC3

Jonas_5 — Fri, 15 Mar 2002 09:14:55 GMT

Hi Marco.

Thanks a lot. You were right about the hardware trouble. I spoke to HP Support in Stockholm yesterday, and today there were a guy from HP and switched the backplane card, so now the server i running like never before.

Have a placent weekend.
Bye. /Jonas