topic Re: netserver lh3 in Netservers

netserver lh3

Qqakele — Fri, 22 Apr 2005 06:15:00 GMT

Hie guys,

I have an old HP Netserver LH3 with two new hard drives. Does anyone know how to install Windows NT operating system without the HP Navigator CDs? I cleared existing raid configurations and did new raid configurations. When i try to install NT, i get a message that reads "...setup could not continue because there were no hard drives detected or ...use manufacturer-supplied diagnostic or setup program"

Re: netserver lh3

Bryan Eley — Fri, 22 Apr 2005 06:42:41 GMT

What kind of raid controller is it? You probably need to hit F6 during NT's initial setup and/or point the installation to a driver disk with the raid controller driver. With the navigator CD HP automatically feeds the required drivers during installation. If you don't have the drivers, let me know. I've got a couple of navigator CDs for my LH4 where LH3 drivers are included such that I could potentially upload the raid controller driver or other files for you.

Bryan

Re: netserver lh3

Bryan Eley — Fri, 22 Apr 2005 07:05:41 GMT

You can also download LH3 drivers from this link:
http://h20180.www2.hp.com/apps/Lookup?h_lang=en&h_cc=us&cc=us&h_page=hpcom〈=en&h_client=S-A-R163-1&h_pagetype=s-002&h_query=lh+3

Re: netserver lh3

e4services — Sat, 23 Apr 2005 10:42:37 GMT

THat is correct. You do not have the driver support loaded during the install to support the RAID controller, therefore the OS setup does not see any disk space because no logical drive exists for it.

Re: netserver lh3

amhakassa — Sat, 23 Apr 2005 22:26:54 GMT

Hi Q,

You already got the driver link from Bryan so no need to mention that again. However, you have mentioned that you reconfigured your array, if that is he case make sure you initialized the newly configured logical drive. If you have trouble doing so let me know

Regards
Amha kassa

Re: netserver lh3

Qqakele — Mon, 25 Apr 2005 04:33:51 GMT

Hie all

Thank you all for your responses.

Bryan,i am using an integrated HP Netraid controller. I downloaded the drivers from the link you gave me and tried it. During setup i specified additional drivers and pointed to the disk with the drivers. There are four additional drivers and i chose the first one, that of Netserver LH3 embedded SCSI. After specifying that, the setup program realised and loads the drivers.

However when i go to the next step of the installation i still get the same message that no hard disks were detected.

You assistance is highly appreciated.

Regards Q

Re: netserver lh3

Mario_66 — Mon, 25 Apr 2005 05:14:18 GMT

Hi,

as far as I remember, you should use driver for HP NetRAID (I or II) and not for embedded SCSI. I assume that you configured logical volume through RAID utility and initialized it.

HTH,
Mario.

Re: netserver lh3

Qqakele — Mon, 25 Apr 2005 08:50:18 GMT

Hi all

The driver for HP NetRAID I or II recommended by Mario is on the internet but unfortunately i cannot download it. I get an ftp error each time i try to download it. Can someone please upload the file for me? I appreciate your help. Thank you in advance.

Rgds Q

Re: netserver lh3

Mario_66 — Mon, 25 Apr 2005 09:25:22 GMT

Hi,

sorry, my mistake.

Have you already downloaded "hp netserver lh 3 Drivers for NT 4.0"? I assume that you have, because you mentioned that you selected "embedded SCSI driver".

So, if you have that diskette, please try the second entry ""Hewlett-Packard NetServer NetRAID RAID Controller" or something else which looks like this one.

It should work, at least it worked for me last time. If you still have a problem, I will try to do the same tomorrow morning on my LH3 test server.

Best regards,
Mario.

Re: netserver lh3

amhakassa — Mon, 25 Apr 2005 15:53:02 GMT

Hi Q,

It is not Netraid I or II that you need.

The driver that you need is "integrated raid controller raid driver" here is the link where to download it

http://h20000.www2.hp.com/bizsupport/TechSupport/DriverDownload.jsp?locale=en_US&pnameOID=15389&taskId=135&prodTypeId=15351&prodSeriesId=50440〈=en&cc=us&swEnvOID=24

After You load the driver make sure you pressed S again to select the CD ROM (ATAPI CDROM) Otherwise you might end up with no CD ROM found. (the Choose the CD ROM you have to scrool all the way up in the list)

Regards
AMha Kassa

Re: netserver lh3

amhakassa — Mon, 25 Apr 2005 15:55:31 GMT

HI Q,

Actually here is the best place to get the right driver for the integrated raid controller
http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?locale=en_US〈=English&pnameOID=62470&prodSeriesId=51919&prodTypeId=329290&basePartNum=ns2032&locBasepartNum=ns2032en&os=Microsoft+Windows+NT+4.0&tech=Driver++Storage+Controller

Regards
Amha Kassa

Re: netserver lh3

Bryan Eley — Mon, 25 Apr 2005 16:22:57 GMT

Yes, I agree with Amhakassa that that driver should work best. I *think* that is the version that was on my "M" version Netserver navigator CD that I was looking at. Let us know how it works!

Re: netserver lh3

Qqakele — Thu, 12 May 2005 03:44:28 GMT

Hie All,

Thank you all for the assistance. i managed to do it with Windows NT 4 boot disks and the drivers from the links you gave me. I worked out very well.

Regards Q