topic Re: Netserver LX Pro Hangs... in Netservers

Netserver LX Pro Hangs...

Damion Jedlicka — Wed, 21 Nov 2001 05:49:57 GMT

I was given an LX Pro 6/200 (i think) from work and I can't get it to boot. The drive cages startup and there are three beeps when i power it up. But there is no video to the monitor (although it seems like it has sync) and it's LCD show one line w/ all black.

Anyone have any ideas? I've tried CMOS clear. And that had no effect.

(Could it be a bad system board?)

Re: Netserver LX Pro Hangs...

himem — Wed, 21 Nov 2001 09:34:46 GMT

From 3 beeps error, I think it is first 64K memory test failure, maybe you should check and replace SIMMs inside your lx pro.

Re: Netserver LX Pro Hangs...

Marino Meloni_1 — Wed, 21 Nov 2001 14:52:30 GMT

hi
himem is right, here is the list of beep code for lx

1 Refresh failure Replace the system board
2 Parity cannot be reset Replace the system board
3 First 64K memory failure Check and replace SIMMs
4 Timer not operational Replace the system board
5 Processor failure Replace processor board
6 8042 gate A20 is off (v-mode) Replace the system board
7 Exception interrupt error Replace the system board
8 Display memory read/write error Video problem: replace system board for on-board video OR replace installed video board.
9 ROM checksum error Reflash ROM; replace system board
10 Shutdown register read/write error Replace the system board

take in mind that the simm need to folow somes rules, the first is that you need to ad thed memory, four at a time.
bye
marino

Re: Netserver LX Pro Hangs...

Damion Jedlicka — Wed, 21 Nov 2001 17:06:34 GMT

I've tried replacing the simms w/ ones from a working system. Could it be the memory board?

Re: Netserver LX Pro Hangs...

John Borders — Mon, 03 Dec 2001 15:59:36 GMT

Make sure nothing's plugged into it (like network cables). Mine wouldn't boot unless I did that!
John

Re: Netserver LX Pro Hangs...

Samir_23 — Thu, 06 Dec 2001 10:57:38 GMT

hi

I also faced the same problem.

I tried changing the memory board.Finally we changed the system board and it started working

Now it's booting like a horse.Check whether all the jumpers in the correct position.u can see it visually here.

"http://netserver.hp.com/support/parts_service/system_board/sys_board_tpl.asp?pid=LXPro"

bye
renjith

Re: Netserver LX Pro Hangs...

Dan Brown_2 — Thu, 17 Jan 2002 12:08:21 GMT

One thing we have found with hte LX Pro is that if you have an up to date keyboard plugged in, ie one with a windows key on it, it will not boot at all!!

Try it with an old keyboard, with no windows key,

Dan

Re: Netserver LX Pro Hangs...

Gordon Black_2 — Wed, 21 Aug 2002 19:11:49 GMT

I have a LX Pro that was donated to us. It will not boot. I have changed the system board and the memory board. I used a older keyboard without the Win95 key. I have started it with CMOS clear and it will beep 3 times. When we first got it it booted once after I reseated the boards. After that it quit booting at all. I have reseated and visual inspected the boards and could see no problems. I verified the system board switch and jumper settings. I tried it with the NIC and NetRaid removed. No video comes up so it doesn't get far enough into the boot to give me any clues on failure. The management board has a flashing green led. Front panel is green leds. It should be noted that one system board would generate 3 beeps (even with CMOS clear off) which indicated memory. I replaced memory and had same problem. Then replaced memory board and still same problem. We are a non-profit homeless shelter so spending more money on parts is not a good option. Is there anything else I should try before giving up?

Re: Netserver LX Pro Hangs...

Greg Carlson — Wed, 21 Aug 2002 19:44:12 GMT

Gordon,

Please start a new thread so that you can assign points as this is a real old thread.

Ciao,
Greg