topic Re: ML110 G6 B110i Raid 1 option missing in ProLiant Servers (ML,DL,SL)

ML110 G6 B110i Raid 1 option missing

n0fx — Tue, 14 Dec 2010 19:05:44 GMT

I purchased a ML110 G6 server and I've been trying to setup the Raid for the server. When I go into the ORCA, the only options I get to create a raid is Raid 1+0 and Raid 0, there is no options for Raid 1! I have two of the same identical SATA hard drives and they are being detected in the ORCA.

I tried contacting HP support and their suggestion was to update the firmware for the Raid card, which I could NOT find. I found a firmware update for the BIOS, which I applied on the server (rom 27).

I plugged the hard drives to SATA port 1 & 2, is there something specific I need to go get the Raid 1 option to show up? I've setup RAID's before on other servers in the past.

Re: ML110 G6 B110i Raid 1 option missing

Michael A. McKenney — Tue, 14 Dec 2010 19:39:41 GMT

Did you try RAID 1+0 on just two drives? I saw a workstation board with only RAID 1+0 and it worked for two drives.

Re: ML110 G6 B110i Raid 1 option missing

n0fx — Tue, 14 Dec 2010 20:07:38 GMT

I did try that. I created 1 logical drive array, booted up the Windows 2003 SBS disc, loaded the driver from HP to detect the logical array, partitioned the hard drive into two pieces, formatted the first one and installed the Windows files in there. After the initial text based setup, rebooted and it could not boot up.

I tried looking inside ORCA to see if I can set the logical array bootable but there are no options to do so.

Is ORCA supposed to have a Raid 1 option or am I supposed to use Raid 1+0 for Raid 1? The documentation from the raid controller doesn't say anything about it.

This is how my screen looks:

http://img706.imageshack.us/img706/9550/hpml110g6.jpg

Re: ML110 G6 B110i Raid 1 option missing

Wayne Henegar — Wed, 15 Dec 2010 01:23:20 GMT

Here are my notes from the last setup I did. As I recall, you have to change the BIOS first.
-----------------
ML110 G6 server
Raid Configuration
See â Enabling and Configuring the controllerâ
B110i SATA RAID

Set up RAID F10 â BIOS â HD, exit
F8 - Config RAID

--------------
Check Page 5 below.

http://h20000.www2.hp.com/bc/docs/support/SupportManual/c01706551/c01706551.pdf

I have 2 ML110 running Raid 1 with identical drives.

Good luck

Re: ML110 G6 B110i Raid 1 option missing

Ali — Wed, 15 Dec 2010 02:17:25 GMT

Hi there,

There isn't any option for Raid 1 in ACU or ORCA for smart array controller

You have only 1+0 option in ACU and ORCA for both the raid level (Raid 1 Raid 1+0)

How this works is if you have two hard drives it will create Raid 1 and if more than 2 equal no of hard drives then it will create Raid 1+0.

ACU reference guide
http://bizsupport2.austin.hp.com/bc/docs/support/SupportManual/c00729544/c00729544.pdf

Hope this clarifies your doubts.

thanks.
Aftab

Re: ML110 G6 B110i Raid 1 option missing

n0fx — Wed, 15 Dec 2010 03:29:00 GMT

Oh, thanks for clearing that up. I had a hard time wondering if the option was just missing. The manual doesn't really state that the Raid 1+0 doubles up as Raid 1 or 1+0.

Re: ML110 G6 B110i Raid 1 option missing

Ali — Wed, 15 Dec 2010 03:35:05 GMT

Hi Nofx,

excellent!

Please don't forget to assign points if you think information provided was helpful.

thanks,
Aftab

Re: ML110 G6 B110i Raid 1 option missing

n0fx — Wed, 15 Dec 2010 04:09:20 GMT

I'll post points after I got the problem resolved. I haven't had a chance to try out the solution on the server but I should be able to tomorrow.

Re: ML110 G6 B110i Raid 1 option missing

gregersenj — Thu, 16 Dec 2010 14:11:17 GMT

HP has simpified the setup of the RAID controller, leaving fewer levels to choos from.

RAID 1+0 using 2 disks give you a RAID 1.
RAID 1+0 is a number of mirror sets (RAID 1)
that is stripped (RAID 0)
If you have got a even number of disks, lets say 6, and choose RAID 1+0, then it will create 3 mirror sets, and stripe those 3 mirror sets.
Having only 2 disks, it will create 1 RAID 1, and it got no more mirror sets to strip with, so you now got yourself a RAID 1.

BR
/jag

Re: ML110 G6 B110i Raid 1 option missing

n0fx — Thu, 16 Dec 2010 17:35:05 GMT

I got it fixed, thanks for the help guys. I got it up and running last night.

Re: ML110 G6 B110i Raid 1 option missing

n0fx — Thu, 16 Dec 2010 17:35:42 GMT

Solution found for problem, it's working now.