topic SATA HDD Driver Issue when trying to install Windows Server 2008 R2 on Proliant ML110 G5 in ProLiant Servers (ML,DL,SL)

SATA HDD Driver Issue when trying to install Windows Server 2008 R2 on Proliant ML110 G5

strocky — Wed, 21 Jun 2017 11:40:24 GMT

Hi there, I'm running into an issue trying to install Window 2008 R2 Server on my Server

I can't find the correct driver to allow the O/S to be installed on any my 6 HDD's I (keep getting a partition error when I select any of the HDD's that are empty)

I can upload my LOG file if required

I've tried several drivers to no avail along with using the PARTDISK cmd to prep the drives

I just want to run the disks in a non-raid configuration

Any ideas where I can find the correct driver?

Regards Strocky

Re: SATA HDD Driver Issue when trying to install Windows Server 2008 R2

System_Headache — Mon, 19 Jun 2017 15:14:11 GMT

Hello,

From the sound of it, you have a controller card connecting those six hard disk drive. If you want the Operating System to properly install on those HHD, you need to tell us a few things:

The model of the server?
Are they (HDD) connected to a controler card or directly on the motherboard?
If a controller card is present, what is the model?
Are you running a RAID?

Let us know because with Win2008R2, it is much easier to just plug a USB drive with the *.inf drivers to the respective hardware so that the OS detects and installs properly.

Let us know if you have any concerns or questions.

Good day!

Re: SATA HDD Driver Issue when trying to install Windows Server 2008 R2

strocky — Mon, 19 Jun 2017 18:14:34 GMT

Hi there the model is Proliant ML110 G5

Not got the server in front of me but certain it's controller is integrated into the Motherboard

Running non-raid, when I do turn raid on in bios, it lists HDD's as JBOD

Strocky

Re: SATA HDD Driver Issue when trying to install Windows Server 2008 R2

Erdogan Temur — Mon, 19 Jun 2017 19:39:26 GMT

Hi,

You can use the following driver.

HP Embedded G5 SATA RAID Controller Driver for Microsoft Windows Server 2008 x64 Editions
http://h20566.www2.hpe.com/hpsc/swd/public/detail?sp4ts.oid=3577726&swItemId=MTX_7f78089fea9942729f92878330&swEnvOid=4064#tab-history

Re: SATA HDD Driver Issue when trying to install Windows Server 2008 R2

strocky — Mon, 19 Jun 2017 20:03:34 GMT

Thanks, will test in the morning and give feedback

Re: SATA HDD Driver Issue when trying to install Windows Server 2008 R2

strocky — Tue, 20 Jun 2017 08:55:10 GMT

Morning, tried installing the driver at the load driver stage of Windows Server 2008 R2, it finds the ADAPTEC SERIAL ATA HOST RAID (aarahci.inf) driver, loads the driver but then still gives me the same issue

"We couldnt create a new partition or locate an existing one"

This is despite me prepping the HDD using DISKPART with the following commands CLEAN, CREATE PARTITION PRIMARY, FORMAT NTFS & ASSIGN Driver letter

Do i need to slipstream the driver into the USB ISO?

I can upload the LOG file if required?

Re: SATA HDD Driver Issue when trying to install Windows Server 2008 R2

Erdogan Temur — Tue, 20 Jun 2017 09:05:50 GMT

@strocky

Did you do the raid configuration?

Re: SATA HDD Driver Issue when trying to install Windows Server 2008 R2

AlexDBall — Tue, 20 Jun 2017 09:40:39 GMT

Hi,

Is the error "We couldnt create a new partition or locate an existing one" or "We couldnt create a SYSTEM partition or locate an existing one" ?

If the latter is true, one possible solution would be to remove all drives except the one you want to install the OS onto and try running windows setup again.

I had this issue recently on a similar server and by removing any additional hard drives from the server allowed me to perform the installation.

Re: SATA HDD Driver Issue when trying to install Windows Server 2008 R2

strocky — Tue, 20 Jun 2017 10:12:43 GMT

Hi there, No, as I don't want to run raid and lose the data thats already on the other 4 drives

I have 6 Drives in total, 2 blank, 4 with data

The server is only used as a dumb filesharer and to run a few media apps in the background

@Erdogan Temur

EDIT, apologies, Raid was activated and shows the drives as JBOD

If I turn off RAID on the BIOS, Windows Server doesn't recongnise the Adaptec Driver

Re: SATA HDD Driver Issue when trying to install Windows Server 2008 R2

strocky — Tue, 20 Jun 2017 10:00:33 GMT

Morning, it's the FORMER, no mention of System

However that might be a good idea to just have the one HDD installed to start with, as the O/S install is assigning drive letters including C Drive to the other drives

Will give it a try

Re: SATA HDD Driver Issue when trying to install Windows Server 2008 R2

strocky — Tue, 20 Jun 2017 10:10:45 GMT

Does RAID have to be enabled to enable SATA ONLY on this server??

Re: SATA HDD Driver Issue when trying to install Windows Server 2008 R2

strocky — Tue, 20 Jun 2017 12:56:35 GMT

@AlexDBall

Thanks your tip worked, didn't even need to load any 3rd party drivers, cheers