topic Re: Can't access into Intelligent provisioning in ProLiant Servers (ML,DL,SL)

Can't access into Intelligent provisioning

Madubashana — Sat, 21 Apr 2018 15:52:40 GMT

When I’m trying to access intelligent provisioning (HP ProLiant ML310e Gen8 2 ) using F10 it didn’t appears. Instead accessing to intelligent provisioning, after one beep it boot the operating system.

I tried to reinstall the intelligent provisioning using burned disk. After boot server using intelligent provisioning disk it trying to reinstall but after few seconds it shows “Error flashing the NVRAM”

Massage and restart the server.

Resetting NVRAM using ROM-Based Setup Utility and System Maintenance Switch didn’t worked.

Still appears the same error.

Really apricate your assistant on this issue…

Re: Can't access into Intelligent provisioning

Kiran_servers — Sun, 22 Apr 2018 05:38:03 GMT

Hello Madubashana,

Please let me know what is the IP Version which you are trying to install and also have you tried clearing NVRAM using the system Maintenance switch on the system board?

Re: Can't access into Intelligent provisioning

Madubashana — Sun, 22 Apr 2018 14:08:52 GMT

Hello Kiran servers,

Thanks for your response. The IP version trying to install is 2.50

Yes. I cleaned NVRAM using system Maintenance switch but the result is same as before.

tried all methods in bellow link but problem still exists.

https://support.hpe.com/hpsc/doc/public/display?docId=mmr_kc-0101397

Re: Can't access into Intelligent provisioning

Kiran_servers — Sun, 22 Apr 2018 15:25:46 GMT

Hi,

Could you please install 1.64(b) version of IP as 1.x series is for gen9 servers and 2.x series is for gen9 servers.

Re: Can't access into Intelligent provisioning

Madubashana — Sun, 22 Apr 2018 18:07:08 GMT

Hi,

Tried using IP 1.64(B) but issue is still exists...

I attach the 2 screenshots with this..

Re: Can't access into Intelligent provisioning

Kiran_servers — Sun, 22 Apr 2018 18:25:30 GMT

Ok, please let me know if you are able to access iLO and is there any error in iLO under diagnostic tab on the left side of the navigation bar which indicates embedded flash sd card failed or restarted. And what is the os installed on the server.

Re: Can't access into Intelligent provisioning

Madubashana — Mon, 23 Apr 2018 00:20:50 GMT

After reset ROM-Based Setup Utility to defults can't login to server using iLO also a error showing in iLO when system loading. (watch screenshot)

OS is Windows Server 2012 R2.

Re: Can't access into Intelligent provisioning

Kiran_servers — Mon, 23 Apr 2018 01:13:38 GMT

Hi,
Could you please share the screenshot of iLO diagnostics page.

Regards,
Kiran Kumar

Re: Can't access into Intelligent provisioning

Kiran_servers — Mon, 23 Apr 2018 01:19:48 GMT

And also please check with this article

https://support.hpe.com/hpsc/doc/public/display?docId=emr_na-c04034599

If possible please ref last iLO 4 firmware to the latest version and try reflashing IP using 1.64 recovery media

Re: Can't access into Intelligent provisioning

ChrisHilliard — Fri, 25 Jan 2019 13:59:57 GMT

I had a situation where I had 2 DL380 GEN10 servers that I could not access Intelligent Providioning (IP) nor could I flash NVRAM. I found in ILO that I had the Security Encryption setting to "HighSecurity". I changed the setting to "Production" and reset the ILO interface, I was then able to launch IP.