topic Re: DL380 gen9 Critical Temperature Threshold Exceeded error, not showing sensor info in ProLiant Servers (ML,DL,SL)

DL380 gen9 Critical Temperature Threshold Exceeded error, not showing sensor info

yesuha — Mon, 28 Nov 2022 08:43:44 GMT

Hi to all

im facing a issue with a DL380 GEN9 server, with 1 processor config, fans in 3 4 5 6 slots as the instrucctions says, it wont post, just cycles between amber and green power led, the health led is blinking red, checking IML on ILO 4 reports "Critical Temperature Threshold Exceeded" on every reboot, but it doesn´t show any info about what sensor is sending error or anything else, i tried bios update, ilo update, both flashed succefully, a weird thing i noted is that, there is no info about fans status, only shows status = unknown, same for the power supplies and ram, what the issue could be?

Query: DL380 gen9 Critical Temperature Threshold Exceeded error, not showing sensor info

support_s — Tue, 22 Nov 2022 07:12:12 GMT

System recommended content:

1. Advisory: HPE ProLiant DL380 Gen9 Server - Incorrect Temp threshold Messages May Be Displayed in The Kernel And "Temp Threshold Exceeded"Traps Are Sent to the Management Station on Systems Running the HPE Custom ISO Image for VMware

Please click on "Thumbs Up/Kudo" icon to give a "Kudo".

Thank you for being a HPE valuable community member.

Re: Query: DL380 gen9 Critical Temperature Threshold Exceeded error, not showing sensor in

yesuha — Tue, 22 Nov 2022 15:03:14 GMT

The system is not turning on, justo power cycles, so, how can i update Vmware?

Re: DL380 gen9 Critical Temperature Threshold Exceeded error, not showing sensor info

Sham82 — Thu, 24 Nov 2022 05:58:30 GMT

Hello,

1. please, Power cycle the server once (Perform complete power cycle ( remove all the cables , press and hold the power button for 15seconds) , then try to boot the server.)

2. please perform "Restoring default system settings" Steps in the below link

https://support.hpe.com/hpesc/public/docDisplay?docId=c04398276&page=s_Restoring_Default_System_Settings.html

3. If the issue remains , we will further have to check the H/W logs.
so if the issue remains please log a case with HPE support.

Regards
HPE

Re: DL380 gen9 Critical Temperature Threshold Exceeded error, not showing sensor info

yesuha — Thu, 24 Nov 2022 07:21:07 GMT

Hi, thanks for your response, think we are missing something here, the system won´t boot, just cycles, the power led goes from blinking green, to blinking amber with healt led red, then again starts that cycle, so i can´t enter to Operating System, can´t even enter bios, cause there is no video, it turns on only for 2 seconds and then again blinking amber with healt led red, the only thing i can do, is enter to ilo, so the step 2 you suggest, is not viable, alredy cleaned nvram, and did step 1, with and without cmos battery and even without raid battery, i send captures of the errors ilo "detects" , and some other info about the actual state of the server according to ilo

as you can see, it is not giving any info about temperatures, not giving any info about what sensor is getting "critical temperature"

Re: DL380 gen9 Critical Temperature Threshold Exceeded error, not showing sensor info

Sham82 — Thu, 24 Nov 2022 08:41:05 GMT

Hello,

We suspect, it could be system board issue.
However before we recommend any H/W part , we would need to check the H/W Logs.

Hence please log a support case.

Regards
HPE

Re: DL380 gen9 Critical Temperature Threshold Exceeded error, not showing sensor info

yesuha — Thu, 24 Nov 2022 15:22:48 GMT

ok, i´ll be opening a support case, but, could you give me some advice about how to open a support case?

Re: DL380 gen9 Critical Temperature Threshold Exceeded error, not showing sensor info

Sham82 — Fri, 25 Nov 2022 01:08:03 GMT

Hello,

please use and follow below links :

Technical support phone numbers:
https://www.hpe.com/us/en/collaterals/collateral.a00039121enw.html

Support Case Manager:
https://support.hpe.com/help/en/Content/productSupport/supportCaseManager.html

Regards
HPE

Re: DL380 gen9 Critical Temperature Threshold Exceeded error, not showing sensor info

loancarre — Wed, 22 Feb 2023 15:16:30 GMT

hello,

it seem that i have the same probleme with my DL380e G8.

did you get an anwer ?

Re: DL380 gen9 Critical Temperature Threshold Exceeded error, not showing sensor info

Sunitha_Mod — Fri, 24 Feb 2023 08:02:15 GMT

Hello @loancarre,

Thank you for writing to us! Since you have posted in an old topic and there is no response yet, we would recommend you to create a new topic using the create "New Discussion" button, so the experts can check and assist you further.

Re: DL380 gen9 Critical Temperature Threshold Exceeded error, not showing sensor info

ghuman1398 — Fri, 25 Aug 2023 02:42:11 GMT

Hi,

Were you able to fix the issue? I am experiencing same on dl380 gen9.