topic Re: Disabling iLO in ProLiant Servers (ML,DL,SL)

Disabling iLO

topokin — Tue, 29 Aug 2006 03:35:50 GMT

We have ProLiant servers and one of the features that was never configured on them is iLO, which means the installation is made with default configurations without enabling or disabling iLO. However when connecting to some of the servers through "System Management Homepage", I have systems that report the "Link Status" of "Embedded NEC98431" being in FAILED state.

Since all the servers are being monitored by MOM and HP Management Pack is installed, the problem I have is that the iLO link failed state is generating a considerable alerts. So my question is, how can I disable iLO.

Thanks,
topokin

Re: Disabling iLO

ramesh_naik_ — Tue, 29 Aug 2006 04:41:44 GMT

Hi Topokin,

You can disable it through its BIOS setup (F-8).
After disabling it, there will be a message at POST that the iLO is disabled and the F-8 prompt will not display.
In order to re-enable it you have to check the switch settings (security override) on the system board for each unit.
The security override switch will re-enable the F-8 Prompt at POST so that the user can go back in to re-enable the iLO.

Hope it works!!!

Regards,
rmn

Re: Disabling iLO

weik — Wed, 23 Apr 2025 10:31:22 GMT

Hello topokin

Also you can set "Remote Insight Information" to the "Inactive Agents" (in Control Panel / hp Mangagement Agents).

kurt

Re: Disabling iLO

topokin — Wed, 30 Aug 2006 00:33:14 GMT

Thanks to you all for the tips.

As to the "Remote Insight Informaiton", would I still be getting alerts or entries in "System Managemen Homepage" on degration or failure of other components when it is set to "inactive"?

What surprises me however is that we have about 30 ProLiant Servers with none having iLO configured, but only 9 is reporting this Link-failed state. All the servers have the lates Support Pack installed. Any idea on what could be the cause of this differences.

Thanks,
topokin

Re: Disabling iLO

weik — Wed, 30 Aug 2006 04:25:43 GMT

Hi topokin

>>would I still be getting alerts or entries
>>in "System Managemen Homepage" on
>>degration or failure of other components
>>when it is set to "inactive"?
Yes it functions on my Servers. The other Agents (NIC, Storage...) are allways displayed in "HP System Management Homepage" on the Server and hp SiM receive the Traps.

>>What surprises me however is that we have
>>about 30 ProLiant Servers with none having
When you open the "HP System Management Homepage" on the Server, are the Agent "Management Processor" on all Maschine displayed?

kurt

Re: Disabling iLO

topokin — Wed, 30 Aug 2006 10:37:58 GMT

Yes I do have "Management Processor" displayed on the "System Management Homepage". Attached is a screen of two different systems, and both are supposed to have default configuration. Which means I did not perform any special configuration in respect of iLO.

Thanks,
topokin

Re: Disabling iLO

Igor Karasik — Thu, 31 Aug 2006 10:15:10 GMT

>>What surprises me however is that we have about 30 ProLiant Servers with none having iLO configured, but only 9 is reporting this Link-failed state.

Any chance you have ILO card connected to network on 21 server where Embedded NEC98431 is not in Failed status ?

Re: Disabling iLO

topokin — Fri, 01 Sep 2006 04:29:56 GMT

Not at all, I do not have any of the iLO port connected. We only use the NICs.

Re: Disabling iLO

weik — Fri, 01 Sep 2006 14:43:19 GMT

How look your Management window from the NECxxx?

Take a look at the my two ILOs. Both have enabled Agents. The "orange" ilo is enabled on the Systemboard. The "blue" is disabled on the board.

Are the Servers with the error all the same model?

Re: Disabling iLO

topokin — Thu, 07 Sep 2006 04:16:47 GMT

In my case, ilo is enabled on the Systemboard of all the 30 servers. 21 servers reports "OK" while 9 reports "Failed".