topic Re: Problem with boot from DVD my rx7640 in Integrity Servers

Problem with boot from DVD my rx7640

Slawek Ksiazek — Thu, 11 Sep 2008 14:11:44 GMT

Hi
I have new rx7640 and I try boot and install HPUX 11.31 but during boot (EFI)I have mesage

"Selected boot option: Internal DVD (Upper) Cabinet 0 [Acpi(HWP0002,PNP0A03,100)/Pci(3|1)/Scsi(Pun2,Lun0)]

Loading.: Internal DVD (Upper) Cabinet 0 [Acpi(HWP0002,PNP0A03,100)/Pci(3|1)/Scsi(Pun2,Lun0)]

Load of Internal DVD (Upper) Cabinet 0 [Acpi(HWP0002,PNP0A03,100)/Pci(3|1)/Scsi(Pun2,Lun0)] failed: Not Found

Press any key to continue"

What you think about my problem?How can i sove this problem?Please help me.Thanks a lot for help.

Slawek

Re: Problem with boot from DVD my rx7640

Torsten. — Thu, 11 Sep 2008 14:20:35 GMT

Dump question ;-)

Do you have the cd in the upper internal drive? Or should it be the lower?

Re: Problem with boot from DVD my rx7640

Slawek Ksiazek — Thu, 11 Sep 2008 14:35:05 GMT

Hi

I have in internal drive media DVD (HP Mission Critical 11.31 DVD 1 of 2)

Slawek

Re: Problem with boot from DVD my rx7640

Torsten. — Thu, 11 Sep 2008 14:42:05 GMT

Go to EFI shell and run

Shell> reconnect -r
Shell> map -r

Do you see any fs_: entries, e.g. fs0:> ?

Re: Problem with boot from DVD my rx7640

Slawek Ksiazek — Thu, 11 Sep 2008 14:46:02 GMT

In addition

mount /dev/dsk/c5t2d0 /dvdrom
/dev/dsk/c5t2d0: I/O error

Slawek

Re: Problem with boot from DVD my rx7640

Torsten. — Thu, 11 Sep 2008 14:47:59 GMT

Check if you can read / mount the media in another system (you can even try it in your PC).

Re: Problem with boot from DVD my rx7640

Slawek Ksiazek — Thu, 11 Sep 2008 15:01:11 GMT

I can read this dvd media on my laptop,

EFI Boot Manager ver 1.10 [14.61] Loading device drivers
EFI Boot Manager ver 1.10 [14.61] Please select a boot option
OS might use only the primary console set via boot manager or conconfig command

HP-UX Primary Boot: 0/0/0/3/0.0x6.0x0
LAN [Acpi(HWP0002,PNP0A03,101)/Pci(1|0)/Pci(6|0)/Mac(001CC4C5BA2
LAN [Acpi(HWP0002,PNP0A03,101)/Pci(1|0)/Pci(6|1)/Mac(001CC4C5BA2
LAN [Acpi(HWP0002,PNP0A03,102)/Pci(1|0)/Mac(001A4B07FFCE)]
LAN [Acpi(HWP0002,PNP0A03,102)/Pci(1|1)/Mac(001A4B07FFCF)]
LAN [Acpi(HWP0002,PNP0A03,1)/Pci(1|0)/Pci(6|0)/Mac(001CC4C5BA4C)
LAN [Acpi(HWP0002,PNP0A03,1)/Pci(1|0)/Pci(6|1)/Mac(001CC4C5BA4D)
LAN [Acpi(HWP0002,PNP0A03,2)/Pci(1|0)/Mac(001A4B07FDA6)]
LAN [Acpi(HWP0002,PNP0A03,2)/Pci(1|1)/Mac(001A4B07FDA7)]
EFI Shell [Built-in]
Internal DVD (Upper) Cabinet 0 [Acpi(HWP0002,PNP0A03,100)/Pci(3|
Boot Option Maintenance Menu

Use ^ and v to change option(s). Use Enter to select an option
Use > and < to view long descriptions
Hot Key: 'S' or 's' to start the EFI Shell

Selected boot option: EFI Shell [Built-in]

Loading.: EFI Shell [Built-in]

EFI Shell version 1.10 [14.61]
Device mapping table
fs0 : Acpi(HWP0002,PNP0A03,0)/Pci(3|0)/Scsi(Pun6,Lun0)/HD(Part1,Sig82DA0F42-2E12-11DD-8000-D6217B60E588)
fs1 : Acpi(HWP0002,PNP0A03,0)/Pci(3|0)/Scsi(Pun6,Lun0)/HD(Part3,Sig82DA0FA6-2E12-11DD-8000-D6217B60E588)
blk0 : Acpi(HWP0002,PNP0A03,0)/Pci(3|0)/Scsi(Pun6,Lun0)
blk1 : Acpi(HWP0002,PNP0A03,0)/Pci(3|0)/Scsi(Pun6,Lun0)/HD(Part1,Sig82DA0F42-2E12-11DD-8000-D6217B60E588)
blk2 : Acpi(HWP0002,PNP0A03,0)/Pci(3|0)/Scsi(Pun6,Lun0)/HD(Part2,Sig82DA0F88-2E12-11DD-8000-D6217B60E588)
blk3 : Acpi(HWP0002,PNP0A03,0)/Pci(3|0)/Scsi(Pun6,Lun0)/HD(Part3,Sig82DA0FA6-2E12-11DD-8000-D6217B60E588)
blk4 : Acpi(HWP0002,PNP0A03,1)/Pci(1|0)/Pci(4|1)/Scsi(Pun5,Lun0)
blk5 : Acpi(HWP0002,PNP0A03,100)/Pci(3|0)/Scsi(Pun6,Lun0)
blk6 : Acpi(HWP0002,PNP0A03,100)/Pci(3|1)/Scsi(Pun2,Lun0)
blk7 : Acpi(HWP0002,PNP0A03,101)/Pci(1|0)/Pci(4|1)/Scsi(Pun6,Lun0)

startup.nsh> echo -off

setting hpux path(\EFI\HPUX)...
type 'fs[x]:' where x is your bootdisk (0, 1, 2...)
type 'hpux' to start hpux bootloader
Shell> reconnect -r

Scsi(Pun6,Lun0) HP 300 GST3300655LC HPC8 (320 MBytes/sec)
Scsi(Pun5,Lun0) HP 300 GST3300655LC HPC8 (320 MBytes/sec)
PciRom S=00 B=70 D=1 F=0 I=3 loaded at 787FBABD000-787FBAF0000
HP PCI-X 2Port 4Gb Fibre Channel Adapter (driver 1.09, firmware 4.00.090)
HP PCI-X 2Port 4Gb Fibre Channel Adapter (driver 1.09, firmware 4.00.090)
HP PCI-X 2Port 4Gb Fibre Channel Adapter (driver 1.09, firmware 4.00.090)
HP PCI-X 2Port 4Gb Fibre Channel Adapter (driver 1.09, firmware 4.00.090)
HP PCI-X 2Port 4Gb Fibre Channel Adapter (driver 1.09, firmware 4.00.090)
HP PCI-X 2Port 4Gb Fibre Channel Adapter (driver 1.09, firmware 4.00.090)
Scsi(Pun6,Lun0) HP 300 GST3300655LC HPC8 (320 MBytes/sec)
Scsi(Pun2,Lun0) Optiarc DVD RW AD-5170A 1.32 ( 40 MBytes/sec)
Scsi(Pun6,Lun0) HP 300 GHUS153030VL3800 HPC1 (320 MBytes/sec)
HP PCI-X 2Port 4Gb Fibre Channel Adapter (driver 1.09, firmware 4.00.090)
HP PCI-X 2Port 4Gb Fibre Channel Adapter (driver 1.09, firmware 4.00.090)
PciRom S=01 B=8D D=4 F=0 I=0 loaded at 787FBA93000-787FBABD000
PciRom S=01 B=8D D=6 F=0 I=0 loaded at 40FFC3C000-40FFC76000

Copyright (c) 2000-2005 Broadcom Corporation
Broadcom NetXtreme Gigabit Ethernet EFI driver v7.0.11

HP 2Port 2Gb Fibre Channel Adapter (driver 1.47, firmware 3.03.154)
Broadcom NetXtreme Gigabit Ethernet (BCM5703) is detected (PCI-X)
HP PCI-X 2Port 4Gb Fibre Channel Adapter (driver 1.09, firmware 4.00.090)
HP PCI-X 2Port 4Gb Fibre Channel Adapter (driver 1.09, firmware 4.00.090)
HP PCI-X 2Port 4Gb Fibre Channel Adapter (driver 1.09, firmware 4.00.090)
HP PCI-X 2Port 4Gb Fibre Channel Adapter (driver 1.09, firmware 4.00.090)
ReconnectController(0,0,0) : Status = Success

Shell>
Shell> map -r
Device mapping table
fs0 : Acpi(HWP0002,PNP0A03,0)/Pci(3|0)/Scsi(Pun6,Lun0)/HD(Part1,Sig82DA0F42-2E12-11DD-8000-D6217B60E588)
fs1 : Acpi(HWP0002,PNP0A03,0)/Pci(3|0)/Scsi(Pun6,Lun0)/HD(Part3,Sig82DA0FA6-2E12-11DD-8000-D6217B60E588)
blk0 : Acpi(HWP0002,PNP0A03,0)/Pci(3|0)/Scsi(Pun6,Lun0)
blk1 : Acpi(HWP0002,PNP0A03,0)/Pci(3|0)/Scsi(Pun6,Lun0)/HD(Part1,Sig82DA0F42-2E12-11DD-8000-D6217B60E588)
blk2 : Acpi(HWP0002,PNP0A03,0)/Pci(3|0)/Scsi(Pun6,Lun0)/HD(Part2,Sig82DA0F88-2E12-11DD-8000-D6217B60E588)
blk3 : Acpi(HWP0002,PNP0A03,0)/Pci(3|0)/Scsi(Pun6,Lun0)/HD(Part3,Sig82DA0FA6-2E12-11DD-8000-D6217B60E588)
blk4 : Acpi(HWP0002,PNP0A03,1)/Pci(1|0)/Pci(4|1)/Scsi(Pun5,Lun0)
blk5 : Acpi(HWP0002,PNP0A03,100)/Pci(3|0)/Scsi(Pun6,Lun0)
blk6 : Acpi(HWP0002,PNP0A03,100)/Pci(3|1)/Scsi(Pun2,Lun0)
blk7 : Acpi(HWP0002,PNP0A03,101)/Pci(1|0)/Pci(4|1)/Scsi(Pun6,Lun0)

Re: Problem with boot from DVD my rx7640

Slawek Ksiazek — Thu, 11 Sep 2008 15:09:00 GMT

still i can't boot i see

EFI Shell [Built-in]
Internal DVD (Upper) Cabinet 0 [Acpi(HWP0002,PNP0A03,100)/Pci(3|
Boot Option Maintenance Menu

Use ^ and v to change option(s). Use Enter to select an option
Use > and < to view long descriptions
Hot Key: 'S' or 's' to start the EFI Shell

Selected boot option: Internal DVD (Upper) Cabinet 0 [Acpi(HWP0002,PNP0A03,100)/Pci(3|1)/Scsi(Pun2,Lun0)]

Loading.: Internal DVD (Upper) Cabinet 0 [Acpi(HWP0002,PNP0A03,100)/Pci(3|1)/Scsi(Pun2,Lun0)]

Load of Internal DVD (Upper) Cabinet 0 [Acpi(HWP0002,PNP0A03,100)/Pci(3|1)/Scsi(Pun2,Lun0)] failed: Not Found

Press any key to continue

Re: Problem with boot from DVD my rx7640

Torsten. — Thu, 11 Sep 2008 15:11:42 GMT

Devices are here:

Scsi(Pun6,Lun0) HP 300 GST3300655LC HPC8 (320 MBytes/sec)
Scsi(Pun2,Lun0) Optiarc DVD RW AD-5170A 1.32 ( 40 MBytes/sec)
Scsi(Pun6,Lun0) HP 300 GHUS153030VL3800 HPC1 (320 MBytes/sec)

this is
disk
dvd drive
disk

but the system cannot read the media. Can you try another bootable (for Integrity) media?

Re: Problem with boot from DVD my rx7640

Slawek Ksiazek — Thu, 11 Sep 2008 15:19:09 GMT

I have other media with OS but I have this same situation,Plase tell me if on rx serwer are other media with OS than rp machines?

Slawek

Re: Problem with boot from DVD my rx7640

willlee17 — Thu, 06 Nov 2008 17:50:03 GMT

I have this problem, too!

I want to install 11iv2 MCOE on rx8640, but can't boot form DVD.

Selected boot option: Internal DVD (Upper) Cabinet 0 [Acpi(HWP0002,PNP0A03,0)/Pci(2|1)/Scsi(Pun2,Lun0)]

Loading.: Internal DVD (Upper) Cabinet 0 [Acpi(HWP0002,PNP0A03,0)/Pci(2|1)/Scsi(Pun2,Lun0)]

Load of Internal DVD (Upper) Cabinet 0 [Acpi(HWP0002,PNP0A03,0)/Pci(2|1)/Scsi(Pun2,Lun0)] failed: Not Found

Anybody can help me?

Re: Problem with boot from DVD my rx7640

Slawek Ksiazek — Thu, 06 Nov 2008 18:52:56 GMT

Was broken DVD drive (I'd like add that dvd drive have two lasers one for dvd and secound for cd's)

Slawek

Re: Problem with boot from DVD my rx7640

willlee17 — Tue, 11 Nov 2008 12:26:02 GMT

My OS DVD disc is damaged, although I can mount it in OS and swlist can list the content of it.

When I use another OS version DVD, I can boot from it.

Maybe the header(MBR) of DVD is bad, I think!