topic Re: OpenVMS Alpha V8.2 OPA0 - illegal function code with SET TERM in Operating System - OpenVMS

OpenVMS Alpha V8.2 OPA0 - illegal function code with SET TERM

Colin Butcher — Tue, 06 Sep 2005 14:44:16 GMT

I've just upgraded my PWS500au to V8.2 (with all the current patches). Works fine, bar a slight oddity with OPA0: where SET TERM /DEV=VT400/WID=132/PAG=36 (or any SET TERM) produces the error %SET-W-NOTSET, error modifying OPA0: -SYSTEM-F-ILLIOFUNC, illegal I/O function code

Used to work fine on V7.3-1 and on V7.3-2. I assume it's a 'casualty' of the console changes for the Integrity platform.

Workaround is that I just stick the 9pin cable into a different port on the back...

SYSTEM on XDVMS2 $ set term /dev=vt400/wid=132/pag=36
%SET-W-NOTSET, error modifying OPA0:
-SYSTEM-F-ILLIOFUNC, illegal I/O function code
SYSTEM on XDVMS2 $ sho term
Terminal: _OPA0: Device_Type: Unknown Owner: OPA0_SYSTEM
Username: SYSTEM

Input: 9600 LFfill: 0 Width: 80 Parity: None
Output: 9600 CRfill: 0 Page: 24

Terminal Characteristics:
Interactive Echo Type_ahead No Escape
No Hostsync TTsync Lowercase No Tab
Wrap Scope No Remote No Eightbit
No Broadcast No Readsync No Form Fulldup
No Modem No Local_echo No Autobaud No Hangup
No Brdcstmbx No DMA No Altypeahd Set_speed
No Commsync Line Editing Overstrike editing No Fallback
No Dialup No Secure server No Disconnect No Pasthru
No Syspassword No SIXEL Graphics No Soft Characters No Printer Port
Numeric Keypad No ANSI_CRT No Regis No Block_mode
No Advanced_video No Edit_mode No DEC_CRT No DEC_CRT2
No DEC_CRT3 No DEC_CRT4 No DEC_CRT5 No Ansi_Color
VMS Style Input Backspace
SYSTEM on XDVMS2 $

Re: OpenVMS Alpha V8.2 OPA0 - illegal function code with SET TERM

Peter Quodling — Tue, 06 Sep 2005 15:58:03 GMT

Silly question. IS the terminal that you have attached a VT400, or something that is configured to convince the world that it is a VT400?

q

Re: OpenVMS Alpha V8.2 OPA0 - illegal function code with SET TERM

Colin Butcher — Tue, 06 Sep 2005 16:08:42 GMT

It's PowerTerm in VT420 mode. I'm pretty sure that this is a VMS OPA0 issue, not a "device hanging off the end" issue.

The same DCL command works just fine on a non-OPA0 serial port. It used to work just fine on OPA0 as well prior to V8.2 with the same PowerTerm emulator and terminal emulator setup.

It's the "illegal IO function code" that bothers me. Might be PWS500au specific - as in console hardware related.

Re: OpenVMS Alpha V8.2 OPA0 - illegal function code with SET TERM

Peter Quodling — Tue, 06 Sep 2005 16:41:35 GMT

HAve you tried another Terminal emulator? Putty or the like.

btw, I have a PWS500au acquired for VMS work, but it's an ex Eunuchs system, so has the IDE CDrom. How did you get around this, or do you have one of the Cypress chipset versions...

Re: OpenVMS Alpha V8.2 OPA0 - illegal function code with SET TERM

Robert Brooks_1 — Tue, 06 Sep 2005 20:22:41 GMT

Colin wrote . . .

It's the "illegal IO function code" that bothers me. Might be PWS500au specific - as in console hardware related.

Hmmm. ILLIOFUNC is returned by the
device driver's FDT routine if the function code issued is not supported by the driver in question. OPA0 uses OPDRIVER; I'll have a look tomorrow and see if I can reproduce it and if a quick look at the sources reveal anything interesting.

-- Rob

Re: OpenVMS Alpha V8.2 OPA0 - illegal function code with SET TERM

Uwe Zessin — Wed, 07 Sep 2005 00:09:31 GMT

I thought I have seen something similar on old versions and the fix was to add the /PERMANENT qualifier, but I am not 100% sure.

Re: OpenVMS Alpha V8.2 OPA0 - illegal function code with SET TERM

David Jones_21 — Wed, 07 Sep 2005 02:35:18 GMT

I seem to recall a similar message when the alpha console variable "GRAPHICS" rather than "SERIAL".

Re: OpenVMS Alpha V8.2 OPA0 - illegal function code with SET TERM

David B Sneddon — Wed, 07 Sep 2005 02:42:03 GMT

Colin,

Do you have the latest firware installed?
I have a DPW600au running V8.2 plus all patches
and am not seeing any problems.
(I do however have a problem trying to shadow
my system disk, but that is another story)

Dave

Re: OpenVMS Alpha V8.2 OPA0 - illegal function code with SET TERM

Ian Miller. — Wed, 07 Sep 2005 03:16:37 GMT

how is the console configured in the efi firmware?

Re: OpenVMS Alpha V8.2 OPA0 - illegal function code with SET TERM

Antoniov. — Wed, 07 Sep 2005 03:25:45 GMT

Colin,
IMHO you can't modify console on rx series, because same line is used by MP by Ctrl + B.
I guess, MP may have some trouble by any terminal change.

Antonio Vigliotti

Re: OpenVMS Alpha V8.2 OPA0 - illegal function code with SET TERM

Ian Miller. — Wed, 07 Sep 2005 04:02:06 GMT

My mistake - its an alpha not an Itanium. I guess we have to wait until someone with access to the listings can have a look at the console driver

Re: OpenVMS Alpha V8.2 OPA0 - illegal function code with SET TERM

Colin Butcher — Wed, 07 Sep 2005 05:00:14 GMT

This is very confusing. It seems as if the problem is only post-upgrade from V7.3-1 to V7.3-2 to V8.2.

Booting from the V7.3-2 or V8.2 CD the SET TERM /DEV=VT400 works fine at the $$$ prompt.

It also works fine on a clean unpatched V8.2 system installed from the V8.2 CD as a fresh system disc.

The PWS500au has the latest known firmware (V7.2-1) and uses the Cypress chipset.

Details from console output in attached file.

Very strange. I also tried removing the X25 and WANDD products (don't use them any more on this machine) - and that made no difference.

Something is clearly confused about the OPA0 device capabilities, hence the "illegal function code".