topic Re: ILO Amplifier Pack 2.0 in Server Management - Remote Server Management

ILO Amplifier Pack 2.0

BjornM — Fri, 05 Nov 2021 01:26:43 GMT

Hi!

Recently deployed ILO Amplifier Pack 1.95 to have a look at it, but noticed today that there is a 2.0 version out.

Current installation has no internet access, so updating will have to be done manually.

But for some reason i cannot find a file that lets me upgrade from 1.95 to 2.0.

I assume there should be a .bin file or similiar that would let me update ?

Re: ILO Amplifier Pack 2.0

ManBha — Mon, 01 Nov 2021 03:22:23 GMT

Hello,

Please find the link to download version 2.0.

https://myenterpriselicense.hpe.com/cwp-ui/free-software/Z7550-96934

Thanks.

If you feel this was helpful please click the KUDOS! thumb below and accept the solution.

Re: ILO Amplifier Pack 2.0

BjornM — Mon, 01 Nov 2021 08:33:09 GMT

Hi @ManBha

That is the link i tried, but unfortunately, once you click "download" it only allows you to download the vmware, windows or kvm variants, and those are for deploying a new appliance, not for upgrading an old one as far as i've figured out.

Re: ILO Amplifier Pack 2.0

ManBha — Tue, 02 Nov 2021 04:08:18 GMT

Hello,

Please do refer the below document.

https://support.hpe.com/hpesc/public/docDisplay?docId=a00030240en_us&docLocale=en_US

Please do extract the bin file from the zip file as suggested.

Procedure

NOTE: Use the following procedure to upgrade iLO amplifier pack from v1.10 to v1.15 or later releases.

Download and save iLOAmpPack_X.XX_Binary.zip and its corresponding checksum file.

NOTE: Use an appropriate checksum verification tool to verify the integrity of the downloaded files.
Extract iLOAmplifierPack.bin from the zip file.
Save the firmware upgrade file to a removable storage device, network share, HTTP share, or client computer.
Click Configuration and Settings from the left navigation menu, and then click System Update.
Select the storage type that corresponds to the location where user saved the firmware upgrade file.
Depending on the storage type user selected, do one of the following:
- For removable storage (USB), select the mounted device or enter the file path in the format /folder/ filename.
  
  NOTE: USB mounting is supported only in iLO amplifier pack installed using VMware ESXi or KVM.
- For a network share, enter a file path in the format /folder/filename, an IPv4 or IPv6 address, and the network storage path.
- For an HTTP file share, enter the URL for the firmware upgrade file.
- For a file upload, click Browse, and then navigate to the firmware upgrade file on the client computer.
Click Update system manually.

The system will reboot after the update is finished.

NOTE: The IP address of the appliance might change after reboot if iLO amplifier pack is configured with DHCP.
Clear the browser cache.
NOTE:
- The update will fail if jobs are still running.
- Keep the initial registration email for use with future updates.

Thanks.

If you feel this was helpful please click the KUDOS! thumb below and accept the solution.

Re: ILO Amplifier Pack 2.0

BjornM — Tue, 02 Nov 2021 08:38:10 GMT

@ManBha

I have downloaded the only .zip file that is available from your download link. However, that .zip file does not contain any .bin file in it.

The iLOAmpPack_X.XX_Binary.zip file described in the documentation you refer to, does not exist in the download section.... as you can see in the screenshot below.

Re: ILO Amplifier Pack 2.0

MikeGolf299 — Wed, 03 Nov 2021 08:52:48 GMT

Hi @BjornM

I can also confirm the same issues you are facing,

Though I am on an internet facing installation of iLO Amplifer and it is not detecting any new updates from 1.95.

looking as though I may have to re-depploy 2.0 from scratch.

Would be keen to find where this xxx.BIN is hiding though.

Re: ILO Amplifier Pack 2.0

BjornM — Wed, 03 Nov 2021 09:07:27 GMT

@MikeGolf299

Nice to know it's not me being blind, and that the file(s) are actually missing.

Re: ILO Amplifier Pack 2.0

MikeGolf299 — Wed, 03 Nov 2021 11:33:23 GMT

Hi @BjornM,

As there seems to be no official guidance to this missing "iLOAmplifierPack.bin" and the CVE is still standing I have went ahead and deployed the 2.00 appliance.

I have a backup of the 1.95 appliance so essentially rebuilt the 2.00 with all the same networking as the 1.95 appliance, just before I finalized the deployment I powered down my 1.95 Appliance.

The 2.00 Appliance booted up and I was able to log in, from here I performed a Restore from the GUI, this seems to be pretty effictive as I use iLOAmplifer to report into infosight so this connection was re-established as well as all the discovery settings for my subnets.

Very little impact, I will continute to finish the configuration and add in my baselines but for the most part this seems to be the eastest way to get up to 2.00 without hunting for the elusive .BIN.

When deploying the 2.00 Appliance select "initial Deployment" and deploy as a new appliance.

Hope this helps,

Thanks

Re: ILO Amplifier Pack 2.0

BjornM — Wed, 03 Nov 2021 11:40:18 GMT

@MikeGolf299

Thanks for the update.

I guess i'll try to be patient for a little while longer, but eventually i'll cave in and just redeploy everything from scratch i guess. Nice to know that backup/restore works, even between versions.

But hopefully someone at HPE will eventually read this, and fix the download so it also contains the .bin file needed to upgrade existing installations.

Re: ILO Amplifier Pack 2.0

aireynol — Wed, 03 Nov 2021 22:43:08 GMT

Here is the advisory for CVE-2021-29212:

Document - Bulletin: iLO Amplifier Pack - Remote Unauthenticated Directory Traversal Remote Code Execution Vulnerability on iLO Amplifier Pack Versions 1.80, 1.81, 1.90 and 1.95 | HPE Support

Looks like an update will not be made available and re-install is mandatory. Also need to update the password on all managed iLO devices post upgrade. Yikes!

Re: ILO Amplifier Pack 2.0

cesarpegado — Tue, 09 Nov 2021 11:47:04 GMT

I've just been hunting around for this update as well. If there is a HPE person monitoring this thread, can you confirm if an update will be available at a later date. Or am I going to have to backup v1.95 and then restore it in a new V2 version?

Thanks

Re: ILO Amplifier Pack 2.0

JPLIS — Wed, 20 Apr 2022 16:23:27 GMT

The download link is broken - did HPE pull the product altogether?

Re: ILO Amplifier Pack 2.0

aireynol — Wed, 20 Apr 2022 17:12:01 GMT

Same, the download link at https://myenterpriselicense.hpe.com/cwp-ui/free-software/Z7550-96934 is returning a page not found error.

This link from the search results is working though:

https://myenterpriselicense.hpe.com/cwp-ui/product-download-info/Z7550-96934/2.12/sw_free

Re: ILO Amplifier Pack 2.0

Chris Isaksen — Wed, 25 May 2022 13:07:55 GMT

I'm finding the same thing, both those links take me to their new HPE Software Center and it states product not found.

So my guess is that they pulled it and didn't tell anyone. I'm starting to have concerns wiht HPE if this keeps up.I I might have to start looking at aother vendors if they don't get their act together. Though I shouldn't be suprised, HPE webs site hasn't been very good for a long time now. Very diffcult to find what your looking for.

Re: ILO Amplifier Pack 2.0

Sunitha_Mod — Fri, 27 May 2022 08:20:09 GMT

Hello @Chris Isaksen,

Sorry for the inconvenience. If you are still facing the issue, would recommend you to create a support ticket using the following link: https://myenterpriselicense.hpe.com/cwp-ui/contact-us