topic Disk Drive Firmware in Server Management - Systems Insight Manager

Disk Drive Firmware

Pcole — Thu, 26 Jan 2012 10:04:18 GMT

Hi,

Has the ability to be able to update hard disk firmware on ProLiant's using HPSIM disappeared for some reason? I had 2 servers (DL360 and DL380 G5's) which i hadn't been able to patch for a while and both were displaying that they required a hard disk firmware update from HPDE to HPDF.

However, I installed most of the available patches on one of them (think it was support pack 3.60 to 3.70), barring these drive updates; and now the drives are still showing firmware HPDE but as severity normal, with no ability to update them (tick box has gone and the support pack/installed version columns are empty).

Having looked over my other ProLiant servers, these also seem to have lost the ability to upgrade the hard disk firmware and I suspect, if I update the DL360G5 to support pack 3.70, this too will lose the ability.

Is there a reason for this or am I missing a trick?

Thanks

Paul

Re: Disk Drive Firmware

kkpro — Fri, 27 Jan 2012 06:31:35 GMT

Not sure, that you could update hard drive firmware through SIM. Have you tried to update it by hand, using HP Firmware Update CD ?

Re: Disk Drive Firmware

shocko — Mon, 05 Mar 2012 14:47:00 GMT

The Version Control Agent only detects disk drive firmware and makes it available for installation when the WBEM agents are being used as opposed to the SNMP agents. Are you using the WBEM agents?

Re: Disk Drive Firmware

Alwin Warringa — Tue, 09 Apr 2013 13:59:13 GMT

But how do you install WBEM agents on RHEL6 by reading this note:

Notice: Linux - HP Insight WBEM Providers for Linux Has Been Replaced by Agentless Management Through Integrated Lights-Out 4 (iLO 4)

http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?objectID=c03666932&lang=en&cc=us&taskId=101&prodSeriesId=3659620&prodTypeId=18964

Re: Disk Drive Firmware

Pber — Wed, 19 Feb 2014 18:00:11 GMT

I realize this is an old thread, but I have the same issue that others are having.

WBEM is required, and it was working flawlessly up to Version Control Agent 7.1.x.x. Since Version Control Agent 7.2 and above, I have not been able to update disk firmware. The Version Control Agent doesn't even show me the firmware versions anymore either. The server just sends a post alert if the disk firmware needs updating.

If I downgrade my version control agent, it starts working again.

HP please fix.

Re: Disk Drive Firmware

MarkU — Tue, 04 Apr 2017 09:35:35 GMT

It's now 2017 and we are on v7.3.5 of the VCA but this problem remains. I can see the disk firmware version installed but cannot see whether there are any updates or run the updates - as used to happen in earlier versions. How do we know whether a critical firmware update is needed?
Mark

Re: Disk Drive Firmware

Andrew_Haak — Wed, 05 Apr 2017 06:07:58 GMT

Hello,

The VCA/VCRM set is a legacy way of updating your server. The HP preferred way to update your server is by using HP SUM. Did you try to update your server with this tool ? You can even do a remote or scripted (automated) update if you like.

Or do a bunch of servers is that is possible.

Re: Disk Drive Firmware

MarkU — Wed, 05 Apr 2017 14:20:28 GMT

Hi Andrew,
Thanks for your response. We have tried HP SUM but prefer the HP VCR reporting which shows a simple version comparison for each component on a server and a pie chart of the overall update status of a whole group of servers. I realise that VCR isn't getting much support now, but can HP SUM do the same?
Mark