topic Re: On Board Admin WebPage in BladeSystem - General

On Board Admin WebPage

nethunk9 — Wed, 17 Oct 2012 17:20:16 GMT

I am new to blade server.

We have plugged in ilo1and ilo2 are connected to ethernet ports.

This ports are assigned IP address using dhcp.

I can do a telnet to the OA IP addresses i,e both active and standby.

I can also get the login page for ILO1 and ILO2 not sure where to get the credential for the same.

Also I am unable to open the OA webinterface.

Your assistance for getting the above two appointment is highly appreciated

Thank you for sparing some of your time in advance.

Regards

Samir

Re: On Board Admin WebPage

PGTRI — Thu, 18 Oct 2012 06:15:05 GMT

hi,

Reg. the ilo credentials: there is a system maintanence switch on the systemboard of each blade. Locate it and set the switch 1 (

iLO 2 security override ) to ON position. After that you can login to iLo w/o creadiantials and will be able to set a new PW. After doing it , you can put the switch back to OFF.

Reg. the OA login: Do You see the login page ? What is the exactly behavior?

Thanks

regards,

Re: On Board Admin WebPage

nethunk9 — Thu, 18 Oct 2012 07:20:51 GMT

Thank you for your response.

I do not see the login page for the On-Board Administrator. So how do I go about to get the login page?

Regards

Samir

Re: On Board Admin WebPage

PGTRI — Thu, 18 Oct 2012 07:56:40 GMT

hi,

You should assign/configure an IP for the OA using the Insight Display.

Here is the OA user guide.

http://h20000.www2.hp.com/bc/docs/support/SupportManual/c00705292/c00705292.pdf

Thanks

regards,

Re: On Board Admin WebPage

nethunk9 — Thu, 18 Oct 2012 11:07:36 GMT

Hi,

IP is assigned to OA and I can also do ssh and telnet to the active and standby OA.

However when I try to open the OA Webpage i.e https://ip-address it is not accessible

Please suggest

Regards

Samir

Re: On Board Admin WebPage

Torsten. — Thu, 18 Oct 2012 11:48:52 GMT

Try

telnet OA-IP 80

Any answer?

Maybe a browser issue, did you disable the proxy?

Re: On Board Admin WebPage

PGTRI — Thu, 18 Oct 2012 12:10:07 GMT

hi,

What's the FW version of the OA?

Thanks

regards,

Re: On Board Admin WebPage

nethunk9 — Fri, 19 Oct 2012 05:23:10 GMT

It says connection refused.

Re: On Board Admin WebPage

nethunk9 — Fri, 19 Oct 2012 05:26:25 GMT

FW version is 2.6

screenshot attached where it shows connection refused for port 80

and the firmware version

also I tried disabling/enabling https

Re: On Board Admin WebPage

PGTRI — Fri, 19 Oct 2012 06:06:06 GMT

hi,

Your FW version is pretty old. The current one is 3.60. An OA update can resolve the issue. Here is an advisory for a similiar issue.

http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?objectID=c02499458&lang=en&cc=us&taskId=125&prodSeriesId=3540808&prodTypeId=329290

Thanks

regards,

Re: On Board Admin WebPage

SwisspostIT — Fri, 19 Oct 2012 06:39:52 GMT

hi,

also one thing you can try is to reset the OA if you can access it through SSH:

1) login with SSH tool to active OA

2) execute command "restart OA"

after 1-2 minutes try to access web GUI again...

Regards,

Ville

Re: On Board Admin WebPage

SwisspostIT — Fri, 19 Oct 2012 06:41:53 GMT

Ah and Customer Advisory c01077618 could maybe also be an option:

http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?objectID=c01077618&lang=en&cc=us&taskId=130&prodSeriesId=1844065&prodTypeId=329290

(You have other error messages but maybe this is the same issue)

Re: On Board Admin WebPage

panzer_hier — Fri, 19 Oct 2012 10:06:03 GMT

Hi !

1. I had similar problem before, when active oa and standby oa were configured in the same network. So, my suggestions :

Try to unplag standby OA and see what will happen

2. Rarely I experienced stucking of OA web interface, and I reseted it. Use ssh login on active OA and run command

restart oa active

(run help restart in questions)

Dmitry