https://community.hpe.com/t5/bladesystem-general/ilo-problem-bl40p/m-p/4010195#M608 iLO is an independent subsystem located on the main logic board, not on the NIC I/O board. If you replaced the NIC I/O board, that obviously entailed removing the blade and re-inserting, so the usual recommendation of completely cold cycling the blade to clear this error you've already done. So, basically, it's telling you that you need a motherboard replacement. Thu, 31 May 2007 03:44:21 GMT David Claypool 2007-05-31T03:44:21Z https://community.hpe.com/t5/bladesystem-general/ilo-problem-bl40p/m-p/4010194#M607 hi, everybody<BR />i have a problem with a proliant bl40p , that concist in ilo interface...any suggestion???<BR />this is the error...<BR /><BR /><BR />Title: cpqSm2InterfaceError<BR /><BR />Trap Description: "Remote Insight/ Integrated Lights-Out Interface Error.<BR /><BR />The host OS has detected an error in the Remote Insight/ Integrated Lights-Out interface. The firmware is not responding."<BR />Service Action: Revision Date: 1/29/05<BR /><BR /><BR />The Integrated Remote Insight Lights-Out Edition board in the server<BR />PIPDCDBP003 a ProLiant BL40p (Product ID Unknown) with serial number<BR />78JAEMQR2194 has reported an interface error and should be replaced unless the PCI slot has been disabled.<BR /><BR /> <BR />Supporting SNMP data:<BR /> sysName=PIPDCDBP003<BR /> cpqHoTrapFlags=0<BR /> cpqSiSysSerialNum=78JAEMQR2194 <BR /> cpqSiSysServiceNum=78BAEMQR2194<BR /> cpqSiServerSystemId=CPQ0732<BR /> cpqSiProductName=ProLiant BL40p<BR /> cpqHoVersion=5.2<BR /> cpqHoName=Microsoft Windows Server 2003, Standard Edition Service Pack 2<BR /> cpqHoDesc=Service Pack 2, Build 3790 Multiprocessor Free<BR /> sysContact=barron.josue@principal.com<BR /> sysLocation=Monterrey_Prodigy<BR /> cpqSm2CntlrModel=5<BR /> cpqSiSysProductId=<BR /> cpqHoSwVerAgentsVer=7.40.0.0<BR /> cpqSeSysRomVer=I02-09/15/2004<BR /> cpqSeCpuName=Intel Xeon<BR /> cpqSeCpuSpeed=3000<BR /> cpqSm2CntlrBoardSerialNumber=ILO78JAEMQR2194<BR /> cpqSm2CntlrRomRevision=1.82<BR /> cpqSm2CntlrRomDate=8/22/2005<BR /> cpqSm2CntlrSelfTestErrors=0<BR /> cpqHoSwVerVersion=7.40.0.0<BR /><BR /><BR />MSADB filtermap version: 1.52.30<BR />end: cpqSm2InterfaceError<BR /><BR />i change the NIC I/O board and the fail is present today..<BR />the fw on the enclosure is 2.33<BR />ilo fw is 1.89<BR /><BR />regards.... Wed, 30 May 2007 18:16:23 GMT https://community.hpe.com/t5/bladesystem-general/ilo-problem-bl40p/m-p/4010194#M607 eguia 2007-05-30T18:16:23Z https://community.hpe.com/t5/bladesystem-general/ilo-problem-bl40p/m-p/4010195#M608 iLO is an independent subsystem located on the main logic board, not on the NIC I/O board. If you replaced the NIC I/O board, that obviously entailed removing the blade and re-inserting, so the usual recommendation of completely cold cycling the blade to clear this error you've already done. So, basically, it's telling you that you need a motherboard replacement. Thu, 31 May 2007 03:44:21 GMT https://community.hpe.com/t5/bladesystem-general/ilo-problem-bl40p/m-p/4010195#M608 David Claypool 2007-05-31T03:44:21Z