- Community Home
- >
- HPE Community, Taiwan
- >
- Linux
- >
- 系統管理
- >
- 分享我的知識 : Linux may stall when connect to HP MSA st...
系統管理
1748036
會員
4740
線上
108757
解決方案
論壇
類別
Company
Local Language
返回
論壇
討論平台
返回
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
部落格
信息
社區語言
語言
論壇
部落格
文章選項
- 訂閱此主題的RSS 提要
- 將此主題標記為未讀
- 將主題標記為已讀
- 將主題在本帳號置頂
- 標示為書籤
- 訂閱此主題
- 列印此頁
- 將文章標記為未讀
- 標示為書籤
- 訂閱此主題
- 靜音
- 訂閱此主題的RSS 提要
- 高亮顯示此文章
- 列印此文章
- 提報不當內容
在 03-29-2007 12:28 PM
在 03-29-2007 12:28 PM
分享我的知識 : Linux may stall when connect to HP MSA storage
A 2.6 Kernel Linux host (Red Hat and SUSE are this version) may stall during the boot process while loading the Fibre Channel HBA driver if it is connected to an un-configured MSA1000 or MSA1500 running firmware version 5.20 or 7.00. The perceived stall is due to the secondary controller port of the MSA timing out SCSI commands during the driver init procedure. The HBA driver continuously retries these commands for up to 30 minutes in some cases.
If you can not upgrade the MSA firmware prior connecting, try
1.Power on the un-configured MSA1000/1500 with only one array controller installed.
2.Boot the Linux host.
3.From the Linux host, run the Array Configuration Utility (ACU) and create your configuration. Save and exit the ACU.
4.Plug in the secondary controller.
5.From the host, run the command hp_rescan -a to recognize the secondary controller.
6.Run ACU and set up redundancy settings (implicit/explicit), load balancing LUNs, SSP, and so on. Save and exit the ACU.
If you can not upgrade the MSA firmware prior connecting, try
1.Power on the un-configured MSA1000/1500 with only one array controller installed.
2.Boot the Linux host.
3.From the Linux host, run the Array Configuration Utility (ACU) and create your configuration. Save and exit the ACU.
4.Plug in the secondary controller.
5.From the host, run the command hp_rescan -a to recognize the secondary controller.
6.Run ACU and set up redundancy settings (implicit/explicit), load balancing LUNs, SSP, and so on. Save and exit the ACU.
以上表述為作者個人觀點,不代表惠普公司,使用本網站,請遵守網站使用規則和條款
© 版权所有 2024 慧与发展有限责任合伙企业