- Community Home
- >
- Storage
- >
- Midrange and Enterprise Storage
- >
- HPE 3PAR StoreServ Storage
- >
- 3par with direct attached blade enclosure
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-29-2020 11:34 AM
тАО01-29-2020 11:34 AM
I have 3par 8200 direct attached to c7000 blade enclosure through two virtual connect modules. All 3par controllers are connected to the two virtual connect modules using two fabric ,each fabric correspond to a virtual module ,each fabric have two uplink ports one is active the other is standby ,No external san switch connected.
My question is I have a physical rack mount server work as veeam backup server how can I export the luns of the 3par to this physical servers so I can take backup from the luns over san not over lan.
thanks
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-29-2020 01:46 PM
тАО01-29-2020 01:46 PM
Re: 3par with direct attached blade enclosure
Is it safe to export luns to the veeam backup server ??
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-29-2020 11:50 PM
тАО01-29-2020 11:50 PM
Solutionhi
if you don't have a SAN switch your only option is to use one connection from your 3PAR and connect it direct to your VEEAM server. but this means you lose one connection to your servers.
Exporting your Luns to your veeam server is OK they will apear as offline in your disk manager and you must not change that but your backup will be much faster and not go over your network.
you don't need a snapshot license for that. only if you use VEEAM enterprise plus with storage integration than VEEAM uses storage snapshots.
Regards
Give a KUDO if this helps
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-30-2020 06:09 AM
тАО01-30-2020 06:09 AM
Re: 3par with direct attached blade enclosure
Or, add a pair of FC cards.
Note: While I am an HPE Employee, all of my comments (whether noted or not), are my own and are not any official representation of the company
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-02-2020 12:29 AM
тАО02-02-2020 12:29 AM
Re: 3par with direct attached blade enclosure
Thanks for your support
I wonder if I can provide an external switch and connect that external switch to an old Storage IBM just to be for second backup and connect also the virtual connect and the veeam backup server to this external switch ,
Now the senario will be that we have the blade enclosure with virual connect direct attached to the 3par 8200 and also the blade enclosure connected to another fabric attached storaged (Which is IBM) , My Veeam backup physical server will be attached to the external switch , My question is that the veeam server now will be able to see source LUNs from the 3par and destination LUNs (Repository) , what kind of configuration needed to be done on the virtual connect, the external switch and veeam Backup Server . A quick diagram is uploaded to simplify.
Many Thanks