- Community Home
- >
- Storage
- >
- Midrange and Enterprise Storage
- >
- HPE 3PAR StoreServ Storage
- >
- Re: HPE 3PAR and Switch H3C
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-14-2019 11:42 AM
тАО06-14-2019 11:42 AM
Hi,
I'm connected to HPE 3PAR 8200 to an H3C switch through the 10GB SFP connections to present volumes to two DL360 servers.
H3C Comware Platform Software
Comware Software, Version 5.20, Release 1238P08
Copyright (c) 2004-2010 Hangzhou H3C Tech. Co., Ltd. All rights reserved.
H3C S9508E-V uptime is 68 weeks, 4 days, 21 hours, 6 minutes
But it is not doing it, we configure the ports and physically it is observed that there is connection but when looking for the 3PAR there is no connection. When you ping from the switch to 3PAR, the result is negative:
1. The state of the fibers was checked. They are fine.
2. The servers are directly connected to the 3PAR: It works correctly.
3. The comparison was made with another storage system in question of configuration and have the same configuration for the interfaces for the nodes:
#
interface Ten-GigabitEthernet2/0/11
port access vlan 400
jumboframe enable 9216
#
Thank you very much for the help
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-19-2019 05:29 AM
тАО06-19-2019 05:29 AM
Re: HPE 3PAR and Switch H3C
Hello Dimitri_S,
It appears there is a compatibility issue or configuration mismatch.
Did this setup ever work?
Also could you disable jumbo frames and try?
I am an HPE Employee.
[Any personal opinions expressed are mine, and not official statements on behalf of Hewlett Packard Enterprise]
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-19-2019 06:12 AM
тАО06-19-2019 06:12 AM
Re: HPE 3PAR and Switch H3C
Dimitri_S, which ports on the 3PAR are you using? You did get the add-on iSCSI cards for the 3PAR, correct? Please run the following commands and post the results:
showport
showport -iscsi
Note: While I am an HPE Employee, all of my comments (whether noted or not), are my own and are not any official representation of the company
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-10-2019 02:35 PM
тАО07-10-2019 02:35 PM
SolutionHi, Sheldom
3PAR_SYSTEM cli% showport -iscsi
N:S:P State IPAddr Netmask/PrefixLen Gateway TPGT MTU Rate iSNS_Addr iSNS_Port STGT VLAN
0:2:1 ready 0.0.0.0 0.0.0.0 0.0.0.0 21 1500 10Gbps 0.0.0.0 3205 21 Y
0:2:2 offline 0.0.0.0 0.0.0.0 0.0.0.0 22 1500 n/a 0.0.0.0 3205 22 Y
1:2:1 ready 0.0.0.0 0.0.0.0 0.0.0.0 121 1500 10Gbps 0.0.0.0 3205 121 Y
1:2:2 offline 0.0.0.0 0.0.0.0 0.0.0.0 122 1500 n/a 0.0.0.0 3205 122 Y
----------------------------------------------------------------------------------------------
4
I solved the problem.
It was in the VLAN that apparently had not been accepted by switch and likewise configured the gateway to 3PAR and with the problem was overcome.
Thanks.