HPE Community read-only access December 15, 2018
This is a maintenance upgrade. You will be able to read articles and posts, but not post or reply.
Hours:
Dec 15, 4:00 am to 10:00 am UTC
Dec 14, 10:00 pm CST to Dec 15, 4:00 am CST
Dec 14, 8:00 pm PST to Dec 15, 2:00 am PST
3PAR StoreServ Storage
cancel
Showing results for 
Search instead for 
Did you mean: 

remote copy SLD configration

 
SOLVED
Go to solution
kyts
Advisor

remote copy SLD configration

Hello,

We are planning of DR solution using 3PAR SLD(Synchronous Long Distance) configration. 

 

I think that we can kepp the restriction of SLD,,,

 

systen#1, #2 at site A, systen#3 at site B,

Between #1 and #2 using RCFC  “Synchronous Mode”

Between #1 and #3 using RCIP “Asynchronous Periodic Mode”

Betwettn #2 and #3 have an connection as standby link.

 

but, they usually stop remote copy except backup time during nights.

When the time of backup only, it is executed command startrcopy as the time of stoping backup, stoprcopy.

We have the rectriction time for executing 3par remotecopy considering our customer's application.

 

Is That the right way for product support ?

I am worryed in particular remotecopy status is usually stopped. 

 

regargs, 

 

 

6 REPLIES

Re: remote copy SLD configration

No, systems 1 and 2 are synchronous. The Group should always be running.


Note: While I am an HPE Employee, all of my comments (whether noted or not), are my own and are not any official representation of the company.
----------
If my post was useful, click on my KUDOS! thumb below!
kyts
Advisor

Re: remote copy SLD configration

Hello, smith

Thank you for your reply.

 

We just want to do remotecopy from #1 to #2,#3 as same data.

Otherwise, refering manual, we can look the configration of remotecopy for copying for a data to two storage systems is only SLD configration.

 

When we started to discussion of DR site include site B and #3 using SLD configration, it is decided to limit backup time between #1 and #2 as only eight hours par day.

 

Must we decide to change of the time for remotecopy(always sync) ?

 

regards, 

Re: remote copy SLD configration

SLD is to have systems 1 and 2 always in sync. System 3 can have its asynch period adjusted to allow for bandwidth limitations between 1 and 3.

Being a synchronous link, the latency from 1 to 2 can be no more than 2.6 ms. And of course, the same for coming back.


Note: While I am an HPE Employee, all of my comments (whether noted or not), are my own and are not any official representation of the company.
----------
If my post was useful, click on my KUDOS! thumb below!
kyts
Advisor

Re: remote copy SLD configration

Thank you, Smith.

This is the final question of this topic.

 

So, is it the only  way to send volumes from one 3par to two 3pars using remotecopy SLD configration ?

I have recognized remotecopy configration is the three way, 1 to 1, n to n, SLD.

If you know we can adopt another configration, let me know, please.

 

regards,

Solution

Re: remote copy SLD configration

One volume to two target sites, yes; SLD is the only way.


Note: While I am an HPE Employee, all of my comments (whether noted or not), are my own and are not any official representation of the company.
----------
If my post was useful, click on my KUDOS! thumb below!
kyts
Advisor

Re: remote copy SLD configration

Hello, Smith

Thank you very much.

 

I can understand very well.

 

regards,