- Community Home
- >
- Storage
- >
- Midrange and Enterprise Storage
- >
- HPE 3PAR StoreServ Storage
- >
- error when removing permanent magazine, in hp 3par...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-13-2019 01:36 PM
05-13-2019 01:36 PM
Hi,
I have a computer with no warranty, that needs to remove DC4 magazine, which has 3 disk in failure.
For which you initially use the servicemag command but this command did not end well, the servicemag unmark command was executed and the disk lost its pdid,
attached team information
Cage 0, magazine 8:
A servicemag start command failed on this magazine.
The command completed at Wed May 8 16:21:32 2019.
The output of the servicemag start was:
Failed --
Unable to run servicemag Start command. Servicemag is either active or has failed for this cage and magazine.
Please rectify any error conditions and issue "servicemag unmark" before retrying.
servicemag start -wait 0 8 -- Failed
----------------------------------------------------------------------------
# cli% showpd -path
-------Paths-------
Id CagePos Type -State- A B Order
--- 0:8:0 FC new 0:6:1 1:6:1 0/1
--- 0:8:1 FC failed 0:6:1 1:6:1 -/-
--- 0:8:2 FC failed 0:6:1 1:6:1 -/-
--- 0:8:3 FC failed 0:6:1 1:6:1 -/-
----------------------------------------------------------------------------
# cli% showpd
----Size(MB)----- ----Ports----
Id CagePos Type RPM State Total Free A B Capacity(GB)
--- 0:8:0 FC 15 new 559104 0 0:6:1* 1:6:1 600
--- 0:8:1 FC 15 failed 0 0 0:6:1- 1:6:1- --
--- 0:8:2 FC 15 failed 0 0 0:6:1- 1:6:1- --
--- 0:8:3 FC 15 failed 0 0 0:6:1- 1:6:1- --
----------------------------------------------------------------------------
#cli% showversion
Release version 3.2.1 (MU5)
Patches: P39,P49
Component Name Version
CLI Server 3.2.1 (MU5)
CLI Client 3.2.1
System Manager 3.2.1 (P39)
Kernel 3.2.1 (MU5)
TPD Kernel Code 3.2.1 (MU5)
TPD Kernel Patch 3.2.1 (P49)
---------------------------------------------------------------------------
# cli% showcage -d cage0
Id Name LoopA Pos.A LoopB Pos.B Drives Temp RevA RevB Model Side
0 cage0 0:6:1 0 1:6:1 0 36 11-29 2.64 2.64 DC4 n/a
-----------Cage detail info for cage0 ---------
Position: cabinet00 D0
Fibre Channel Info PortA0 PortB0 PortA1 PortB1
Link_Speed 4Gbps -- -- 4Gbps
----------------------------------SFP Info-----------------------------------
FCAL SFP -State- --Manufacturer-- MaxSpeed(Gbps) TXDisable TXFault RXLoss DDM
0 0 OK FINISAR CORP. 4.2 No No No Yes
1 1 OK FINISAR CORP. 4.2 No No No Yes
Interface Board Info FCAL0 FCAL1
Link A RXLEDs Green Off
Link A TXLEDs Green Off
Link B RXLEDs Off Green
Link B TXLEDs Off Green
LED(Loop_Split) Off Off
LEDS(system,hotplug) Green,Off Green,Off
-----------Midplane Info-----------
Firmware_status Current
Product_Rev 2.64
State Normal Op
Loop_Split 0
VendorId,ProductId 3PARdata,DC4
Unique_ID 106203000037FF00
Power Supply Info State Fan State AC Assy_Part
ps0 OK OK OK PO1
ps1 OK OK OK PO1
ps2 OK OK OK PO1
ps3 OK OK OK PO1
-----Magazine Info----- ------------State------------
Mag SysLED HplLED Disks LoopA LoopB
8 Green Off 4 Ready Ready
-------------Drive Info------------- ------------LoopA------------- ------------LoopB-------------
Drive NodeWWN LED Temp(C) ALPA LoopState ALPA LoopState
8:0 2000b45253703f10 Green 27 0xac OK 0xac OK
8:1 2000b45253cc018a Green N/A 0xab Sys Mgr spundown 0xab Sys Mgr spundown
8:2 2000b45253d11b33 Amber N/A 0xaa Sys Mgr spundown 0xaa Sys Mgr spundown
8:3 2000b452537040ac Green N/A 0xa9 Sys Mgr spundown 0xa9 Sys Mgr spundown
------------------------------------------------------------------------------
I will appreciate any possible help.
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-15-2019 06:45 AM
05-15-2019 06:45 AM
SolutionHello Jpalma2001
You would need to vacate the remaining disk in the magazine manually before removing the magazine.
You may find the below threads helpful in removing the PD.
https://www.3parug.com/viewtopic.php?f=18&t=1450
https://community.hpe.com/t5/3PAR-StoreServ-Storage/Remove-a-PD-permanently/td-p/6965032#.XNwXgRQzZ6s
I am an HPE Employee.
[Any personal opinions expressed are mine, and not official statements on behalf of Hewlett Packard Enterprise]