- Community Home
- >
- Storage
- >
- HPE Nimble Storage
- >
- Array Setup and Networking
- >
- New Install CS210
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-14-2013 11:18 AM
тАО07-14-2013 11:18 AM
Hi Everyone,
I wanted to know if someone can assist me with the question That I have.
We recently got a CS210 and I configured the array VIA command line.
I have done the following:
ETH1 on controller A for Management.
ETH2,3,4 for Data.
I did the configuration only on the Controller A. After the configuration was Finished I was able to log onto the Array VIA Browser. I can see the array showing healthy everything is green. I see both controllers A and B and all corresponding ports and connections are green. I have done a failover for testing and I lost connectivity all together.
My questions is, Do I have to run the configuration on both controllers and provide the IP address configuration on Controller B? I only IP Controller A and I thought it is a floating IP scheme as fail over happens it takes the IP from Controller A and assigns it on Controller B?
As far as network goes, we only have one Switch. I know that is not ideal what so ever, but currently we have to configure the Array with Single Switch. Management has its own VLAN and ISCSI has its own VLAN configured. Ports are different for each controllers.
Could Someone please let me know what could have gone wrong?
Regards,
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-14-2013 12:49 PM
тАО07-14-2013 12:49 PM
SolutionHello Sohail,
You only have to configure IP Addresses for the active ports - they will fail over from controller to controller in the event of a failover (eth1 to eth1, eth2 to eth2, and so forth).
Have you plugged in the same eth ports on controller A and B into the same switch? If you only have eth1 configured and plugged in on controller A, yet you have eth2 plugged in on controller B, then failover will not occur because you haven't mirrored the network configuration correctly.
You should have a configuration guide in the array box itself, and you can also get the Installation guide on the "Downloads" section of the support site (sign up here: https://infosight.nimblestorage.com).
If in doubt, give Support a call - they'll be happy to help out.
twitter: @nick_dyer_
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-15-2013 01:18 AM
тАО07-15-2013 01:18 AM
Re: New Install CS210
It all sounds as though it should be correct. You are right - Controller B assumes the same identity as Controller A (with respect to IP addressing and mgmt/data port distribution).
When you say you lost connectivity all together, does this mean management & servers' visibility of LUNs (or just one or the other)?
What do you mean by "ports are different for each controller"? Can you double check your VLAN configs on the switch, just to make sure that the ports from Controller B are in the same VLANs as their partner ports on Controller A? For example:
Controller A, Eth0 (management) - 10.1.1.50 --- VLAN1
Controller A, Eth1 (data 1) - 192.168.1.11 --- VLAN2
Controller A, Eth2 (data 2) - 192.168.1.12 --- VLAN2
Controller A, Eth3 (data 3) - 192.168.1.13 --- VLAN2
Controller B, Eth0 (management) - 10.1.1.50 (inherited) --- VLAN1
Controller B, Eth1 (data 1) - 192.168.1.11 (inherited) --- VLAN2
Controller B, Eth2 (data 2) - 192.168.1.12 (inherited) --- VLAN2
Controller B, Eth3 (data 3) - 192.168.1.13 (inherited) --- VLAN2
iSCSI Discovery address will be tagged to the management port.
It does sound like a networking config discrepancy to me, easily done though. Have you checked AutoSupport works from the array? That'll be useful for Support as/when diagnosing your issue.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-15-2013 08:48 AM
тАО07-15-2013 08:48 AM
Re: New Install CS210
Thank you all for the responses.
It was mistake I made. I had the wrong port numbers written down for the switch.
The correct ports should have been 0/7, 0/8, 0/9, 0/10
I told them to configure 0/8, 0/9, 0/10, 0/11
After the change everything came backup properly.
Thanks again.