Aruba & ProVision-based
cancel
Showing results for 
Search instead for 
Did you mean: 

2810 11.48 firmware, unable to access after applied

 
New Member

2810 11.48 firmware, unable to access after applied

I having some trouble figuring out why after I applied 11.48 to one of my 2810, I was unable able to access it. the switch became isolated.

 

any help would be great, here is the config of the 2810, as well as the config for the 5400 that is it plugged into. From looking at the logs I am thinking that spanning-tree blocked the trunk port, but I cant see why.

 

2810

 J9022A Configuration Editor; Created on release #N.11.15

 

hostname "md213n2" 

snmp-server contact "adminsmc@saintmarys.edu" 

snmp-server location "madaleva 213" 

time timezone -240 

no web-management 

web-management ssl 

ip default-gateway 147.53.2.250 

sntp server 147.53.9.51 

timesync sntp 

sntp unicast 

snmp-server community "hpsmc" Unrestricted 

snmp-server community "smcit" Operator 

vlan 1 

   name "DEFAULT_VLAN" 

   no ip address 

   tagged 47-48 

   no untagged 1-46 

   exit 

vlan 2 

   name "Network" 

   ip address 147.53.2.95 255.255.255.0 

   tagged 47-48 

   exit 

vlan 55 

   name "Madaleva" 

   untagged 1-46 

   no ip address 

   tagged 47-48 

   exit 

vlan 100 

   name "Perfigo" 

   no ip address 

   exit 

vlan 71 

   name "HVAC" 

   no ip address 

   exit 

spanning-tree

password manager

password operator

 

5400

password operator

; J8697A Configuration Editor; Created on release #K.13.63

 

hostname "md213n1" 

web-management management-url "" 

module 1 type J8707A 

module 2 type J8702A 

module 3 type J8705A 

module 4 type J8702A 

interface C13 

   name "a7-108" 

exit

ip default-gateway 147.53.2.250 

timesync sntp 

sntp unicast 

snmp-server community "hpsmc" Unrestricted 

snmp-server community "smcit" Operator 

vlan 1 

   name "DEFAULT_VLAN" 

   untagged A2-A4 

   ip address dhcp-bootp 

   tagged A1,C1,C21-C24 

   no untagged B1-B24,C2-C20,D1-D24 

   exit 

vlan 2 

   name "Network" 

   ip address 147.53.2.94 255.255.255.0 

   tagged A1,C1,C21-C24 

   exit 

vlan 71 

   name "HVAC" 

   untagged D23-D24 

   tagged A1,C1,C21-C24 

   no ip address 

   exit 

vlan 55 

   name "Madaleva55" 

   untagged B1-B24,C2-C20,D1-D10,D19-D22 

   tagged A1,C1,C21-C24 

   no ip address 

   exit 

vlan 100 

   name "Perfigo" 

   untagged D11-D18 

   tagged A1,C1,C21-C24 

   no ip address 

   exit 

sntp server priority 1 147.53.9.51

no ip ssh

spanning-tree

no autorun

password manager

2 REPLIES 2
New Member

Re: 2810 11.48 firmware, unable to access after applied

i had the same problem, ones it work after i reset the switch and applied the saved config file, but only for a few minutes.

i solved the problem, with the old firmware.

=> reset

=> simple setup with IP address

=> downgrade with firmware N.11.25.swi

=> deploy old config file

work again :-)

Good luke

 

Frank

Respected Contributor

Re: 2810 11.48 firmware, unable to access after applied

Hi Mike

 

Please call support. This looks like a bug which should be fixed - but the only way to get that done is making a support case.


HTH,

Arimo
HPE Networking Engineer