- Community Home
- >
- Networking
- >
- Switching and Routing
- >
- Aruba & ProVision-based
- >
- Aruba 5406zl2, cannot configure rate limit bcast o...
-
- Forums
-
- Advancing Life & Work
- Advantage EX
- Alliances
- Around the Storage Block
- HPE Ezmeral: Uncut
- OEM Solutions
- Servers & Systems: The Right Compute
- Tech Insights
- The Cloud Experience Everywhere
- HPE Blog, Austria, Germany & Switzerland
- Blog HPE, France
- HPE Blog, Italy
- HPE Blog, Japan
- HPE Blog, Middle East
- HPE Blog, Russia
- HPE Blog, Saudi Arabia
- HPE Blog, South Africa
- HPE Blog, UK & Ireland
-
Blogs
- Advancing Life & Work
- Advantage EX
- Alliances
- Around the Storage Block
- HPE Blog, Latin America
- HPE Blog, Middle East
- HPE Blog, Saudi Arabia
- HPE Blog, South Africa
- HPE Blog, UK & Ireland
- HPE Ezmeral: Uncut
- OEM Solutions
- Servers & Systems: The Right Compute
- Tech Insights
- The Cloud Experience Everywhere
-
Information
- Community
- Welcome
- Getting Started
- FAQ
- Ranking Overview
- Rules of Participation
- Tips and Tricks
- Resources
- Announcements
- Email us
- Feedback
- Information Libraries
- Integrated Systems
- Networking
- Servers
- Storage
- Other HPE Sites
- Support Center
- Aruba Airheads Community
- Enterprise.nxt
- HPE Dev Community
- Cloud28+ Community
- Marketplace
-
Forums
-
Blogs
-
Information
-
English
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
11-21-2019 01:48 AM
11-21-2019 01:48 AM
Aruba 5406zl2, cannot configure rate limit bcast on trunk ports or trunk member ports
Hello,
I'm trying to implement bcast limit on downlinks/uplinks and cross-building interconnects but I'm receiving message that this feature is not enabled on trunk or trunk member ports. Is there any plan to enable this feature?
Aruba5406(eth-Trk1)# rate-limit bcast in kbps 200
Trk1: Option cannot be set on a trunk.
Aruba5406(eth-1/51)# rate-limit bcast in kbps 200
1/51: Operation is not allowed for a trunked port.
My OS is : KB.16.07.0003
Thank you
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
12-05-2019 12:49 AM
12-05-2019 12:49 AM
Re: Aruba 5406zl2, cannot configure rate limit bcast on trunk ports or trunk member ports
Hi Adam_Kmet,
I have done some research and it seems that the rate limit feature is not configurable on aggregated trunks (trunks).
https://support.hpe.com/hpsc/doc/public/display?docId=emr_na-c01978920
Also in the config guide the below is written for ICMP but it applies for all kinds of rate limiting:
Operating notes for ICMP rate-limiting (Page 224):
Interface support: ICMP rate-limiting is available on all types of ports (other than trunk ports or mesh ports),and at all port speeds configurable for the switch”
https://h20628.www2.hp.com/km-ext/kmcsdirect/emr_na-a00061577en_us-2.pdf
Best regards
Hewlett Packard Enterprise International
- Communities
- HPE Blogs and Forum
© Copyright 2021 Hewlett Packard Enterprise Development LP