Aruba & ProVision-based
cancel
Showing results for 
Search instead for 
Did you mean: 

Cannot get 2920 (J9729a) to route to internet

Geoff_Zieman
Occasional Visitor

Cannot get 2920 (J9729a) to route to internet

I have a test network that I am trying to route to the internet. Works fine at the switch, but not for the clients.  Cannot ping the default gateway (ip address of the DSL router - 192.168.1.254).  I can ping each of the VLANs.

 

Any client attached to VLAN 999 works Ok, just not the other VLANs

 

I have the following:

 

AT&T U-Verse DSL Connection.  IP Address 192.168.1.254

VLANs:  VLAN 100, 192.168.100.1

                VLAN 200, 192.168.200.1

                VLAN 999, 192.168.1.1 (Internet Connection).

 

IP Routing is enabled.

Default route is 0.0.0.0 0.0.0.0 192.168.1.254

 

Client 192.168.100.5 / 255.255.255.0 / 192.168.100.1

 

Current config of 2920-48G PoE+ (J9729A)

-----------------------------------------------------

 ; J9729A Configuration Editor; Created on release #WB.15.17.0008
; Ver #07:eb.8f.fc.f3.ff.37.2d:89

 

hostname "HP-2920-48G-POE+"
 

module 1 type j9729a
ip dns server-address priority 1 192.168.1.254
 

ip route 0.0.0.0 0.0.0.0 192.168.1.254

ip route 192.168.1.0 255.255.255.0 vlan 999
ip route 192.168.100.0 255.255.255.0 vlan 999
ip route 192.168.200.0 255.255.255.0 vlan 999
ip routing
 

snmp-server community "public" unrestricted
 

oobm
   ip address dhcp-bootp
   exit
 

vlan 1
   name "DEFAULT_VLAN"
   no untagged 1-6,47
   untagged 7-46,A1-A2,B1-B2
   tagged 48
   no ip address
   ip igmp
   exit
 

vlan 100
   name "VLAN100"
   untagged 1-4
   tagged 48
   ip address 192.168.100.1 255.255.255.0
   ip igmp
   exit
 

vlan 200
   name "VLAN200"
   untagged 5-6
   tagged 48
   ip address 192.168.200.1 255.255.255.0
   ip igmp
   exit
 

vlan 999
   name "VLAN999"
   untagged 47
   tagged 48
   ip address 192.168.1.1 255.255.255.0
   ip igmp
   exit

 

primary-vlan 999

 

HP-2920-48G-POE+(config)#

---------------------------------------------------------

 

I am sure that this is just a simple routing issue, but I am at a loss at to what it is.  Any help here is usefule.

2 REPLIES
EricAtHP
Esteemed Contributor

Re: Cannot get 2920 (J9729a) to route to internet

Your DSL Router needs a route back to the 2920 for your 100 and 200 subnets.

Geoff_Zieman
Occasional Visitor

Re: Cannot get 2920 (J9729a) to route to internet

Thanks for the Quick Reply.

 

That is what I was thinking, just needed to verify my results.

 

FYI:  AT&T U-Verse "Home" router does not support multiple VLAN configurations.  Only VLAN 1 is available.