- Community Home
- >
- Networking
- >
- Switching and Routing
- >
- Aruba & ProVision-based
- >
- Changing speed on ProCurve J9087A Switch 2610-24-P...
-
- Forums
-
- Advancing Life & Work
- Advantage EX
- Alliances
- Around the Storage Block
- HPE Ezmeral: Uncut
- OEM Solutions
- Servers & Systems: The Right Compute
- Tech Insights
- The Cloud Experience Everywhere
- HPE Blog, Austria, Germany & Switzerland
- Blog HPE, France
- HPE Blog, Italy
- HPE Blog, Japan
- HPE Blog, Middle East
- HPE Blog, Russia
- HPE Blog, Saudi Arabia
- HPE Blog, South Africa
- HPE Blog, UK & Ireland
-
Blogs
- Advancing Life & Work
- Advantage EX
- Alliances
- Around the Storage Block
- HPE Blog, Latin America
- HPE Blog, Middle East
- HPE Blog, Saudi Arabia
- HPE Blog, South Africa
- HPE Blog, UK & Ireland
- HPE Ezmeral: Uncut
- OEM Solutions
- Servers & Systems: The Right Compute
- Tech Insights
- The Cloud Experience Everywhere
-
Information
- Community
- Welcome
- Getting Started
- FAQ
- Ranking Overview
- Rules of Participation
- Tips and Tricks
- Resources
- Announcements
- Email us
- Feedback
- Information Libraries
- Integrated Systems
- Networking
- Servers
- Storage
- Other HPE Sites
- Support Center
- Aruba Airheads Community
- Enterprise.nxt
- HPE Dev Community
- Cloud28+ Community
- Marketplace
-
Forums
-
Blogs
-
Information
-
English
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
09-12-2019 03:00 AM
09-12-2019 03:00 AM
Hi,
I want to change the speed of a port of ProCurve J9087A Switch 2610-24-PWR to support 1000mo
Although when I run this command :
(eth-3)# speed 1000-full
I got this error "Value 1000-full is not applicable to port 3"
The port is (10/100TX) and the mode is MDIX
Any idea?
Thank you.
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
09-12-2019 12:40 PM
09-12-2019 12:40 PM
SolutionImpossible to change speed port to 1000 Mbps (1 Gbps) on Port 3 considering all 24 ports are 10/100 Mbps at maximum (Ethernet/Fast Ethernet not Gigabit Ethernet as you want)...your Switch is a Fast Ethernet Switch with just some ports (25-28) that support Gigabit Ethernet...thus, at best, you can use one of the four Combo ports (ports 25 / 26 are Copper RJ45 Gigabit Ethernet OR ports 27 / 28 are Mini-GBIC for SFP - Fast Ethernet or Gigabit Ethernet - Transceivers <- pay attention that if you use port 25 you can't use prot 27 and viceversa, the same is true for pair 26/28). Definitely port 3 is out-of-question for Gigabit Ethernet, it runs only at 10/100 Mbps speeds.
I'm not an HPE Employee

Hewlett Packard Enterprise International
- Communities
- HPE Blogs and Forum
© Copyright 2021 Hewlett Packard Enterprise Development LP