- Community Home
- >
- Networking
- >
- Switching and Routing
- >
- Aruba & ProVision-based
- >
- Re: Connecting Netgear M4300 to Procurve ALL VLANs
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-01-2018 06:52 AM
тАО06-01-2018 06:52 AM
Connecting Netgear M4300 to Procurve ALL VLANs
Hi,
I have four procurves setup in a mesh but i need to connect a Netgear M4300 switch to one of the procurve switches and carry all VLAN`s across. How would i set this up?
regards,
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-03-2018 05:07 PM
тАО06-03-2018 05:07 PM
Re: Connecting Netgear M4300 to Procurve ALL VLANs
Patch the Netgear in and add all VLANs to that port.
Are you sure you need all VLANs extended to the router? Generally that has a number of downsides, depending on your switch configuration.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-04-2018 03:50 AM
тАО06-04-2018 03:50 AM
Re: Connecting Netgear M4300 to Procurve ALL VLANs
Hi,
I actually only need about 8 VLAN`s to go through from the Netgear to the HP Switch. I wasn`t sure if i had to setup a LAG or not, i presume a normal trunk would suffice?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-06-2018 12:02 AM
тАО06-06-2018 12:02 AM
Re: Connecting Netgear M4300 to Procurve ALL VLANs
In HP terminology, a "trunk" is a LAG. You only need a Trunk if you have multiple physical links.
You need to add all 8 VLANs to the uplink port on the HP switch.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-15-2018 09:37 AM
тАО06-15-2018 09:37 AM
Re: Connecting Netgear M4300 to Procurve ALL VLANs
ok thats`s great..
So where the port that will be the uplink is currently configured as `mesh` do i just need to remove it from the mesh and then set the port to tagged then add the vlans to it?
regards,