Different route for some remote site devices

[spgsitsupport]

I have main site M & satellite site S, linked via 100Mb leased line

All VLAN routing is done by Comware based core on site M

DHCP is supplied from a server in site M

In satellite site S I have HP Procurve 2930F-48G-PoE+-4SFP+ JL256A with no IP assigned to below VLANs

In site S I have some devices (IPCams) attached to above 2930F in VLAN26 as well as a recording server in VLAN9

At the moment (I think) all the recordings travel the leased line twice, up to default gateway of VLAN26 (on core) and back on VLAN9 to the server

What would be the easiest way to make the devices (IPCams) go to the server direct (as they are oin the same switch)

Some static routes per device, do local routing on 2930F?

I am sure it is simple, I just can't see it

That is info from server (accessing the IPCam), both on same 2930F switch

PS C:\> ping 10.10.26.11

Pinging 10.10.26.11 with 32 bytes of data:
Reply from 10.10.26.11: bytes=32 time=21ms TTL=63
Reply from 10.10.26.11: bytes=32 time=2ms TTL=63
Reply from 10.10.26.11: bytes=32 time=2ms TTL=63
Reply from 10.10.26.11: bytes=32 time=1ms TTL=63

Ping statistics for 10.10.26.11:
    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
    Minimum = 1ms, Maximum = 21ms, Average = 6ms
PS C:\> tracert 10.10.26.11

Tracing route to swpool-entrance.domain.local [10.10.26.11]
over a maximum of 30 hops:

  1     *        *        *     Request timed out.
  2     4 ms     7 ms     4 ms  swpool-entrance.domain.local [10.10.26.11]

Trace complete.
PS C:\> route print
===========================================================================
Interface List
  4...24 6e 96 ca 4c 9c ......Intel(R) Ethernet 10G 4P X710/I350 rNDC
 16...24 6e 96 ca 4c 9e ......Intel(R) Ethernet 10G X710 rNDC
  3...24 6e 96 ca 4c bc ......Microsoft Network Adapter Multiplexor Driver
  1...........................Software Loopback Interface 1
===========================================================================

IPv4 Route Table
===========================================================================
Active Routes:
Network Destination        Netmask          Gateway       Interface  Metric
          0.0.0.0          0.0.0.0      10.10.9.254        10.10.9.8    276
        10.10.9.0    255.255.255.0         On-link         10.10.9.8    276
        10.10.9.8  255.255.255.255         On-link         10.10.9.8    276
      10.10.9.255  255.255.255.255         On-link         10.10.9.8    276
        127.0.0.0        255.0.0.0         On-link         127.0.0.1    331
        127.0.0.1  255.255.255.255         On-link         127.0.0.1    331
  127.255.255.255  255.255.255.255         On-link         127.0.0.1    331
        224.0.0.0        240.0.0.0         On-link         127.0.0.1    331
        224.0.0.0        240.0.0.0         On-link         10.10.9.8    276
  255.255.255.255  255.255.255.255         On-link         127.0.0.1    331
  255.255.255.255  255.255.255.255         On-link         10.10.9.8    276
===========================================================================
Persistent Routes:
  Network Address          Netmask  Gateway Address  Metric
          0.0.0.0          0.0.0.0      10.10.9.254  Default
===========================================================================

Thanks

Seb

[akg7]

Hello @spgsitsupport ,

It seems HP Procurve 2930F-48G-PoE+-4SFP+ JL256A is acting a Layer 2.

You have mentioned that server on VLAN 9 is directly connected but I believe Layer 3 is on Main site M for VLAN 9.

If above is correct then L3 traffic should travel to main switch M then reverse to server via L2 switch.

If you want direct traffic then I believe you need to make procurve switch as L3 for VLAN 9.

Can you share network topology diagram?

Thanks!

[spgsitsupport]

Should I not make the 2930F L3 (router VLAN) on both 26 & 9

And make the server & IPCam DG to corresponging IPs

[akg7]

Hi @spgsitsupport,

You can make 2930F L3 (router VLAN)  on both VLAN.

2930F will act as a distribution switch.

Thanks!

[spgsitsupport]

And I need to make the default GW for these devices to be the local switch its VLAN IP, right?

Seb

[akg7]

Hello @spgsitsupport,

Yes its correct.

Thanks!