FCS Rx errors

[AyushGupta]

Hi All,

I have a ProCurve 498358-B21 6120G/XG Blade Switch connected in daisy chain. Its interface 'C1' gets FCS Rx errors. The value increments to a certain number and then stops. The count of FCS Rx errors doesn't go beyond it.

The interface 'C1' is connected to another 6120 Blade Switch. 

We have swapped the cable, but no luck. The errors increment and doesn't go beyond it.

Why does the errors doesn't go beyond 83,412,582. What does it mean?

tec11d-a4ebs03.# sh int c1

Status and Counters - Port Counters for port C1

Name :
MAC Address : 082e5f-f01aa7
Link Status : Up
Totals (Since boot or last clear) :
Bytes Rx : 2,779,753,572 Bytes Tx : 69,109,671
Unicast Rx : 3,944,996,953 Unicast Tx : 374,849,537
Bcast/Mcast Rx : 1,583,974,531 Bcast/Mcast Tx : 1,092,842,043
Errors (Since boot or last clear) :
FCS Rx : 83,412,582 Drops Rx : 0
Alignment Rx : 0 Collisions Tx : 0
Runts Rx : 0 Late Colln Tx : 0
Giants Rx : 1274 Excessive Colln : 0
Total Rx Errors : 83,451,663 Deferred Tx : 0
Others (Since boot or last clear) :
Discard Rx : 0 Out Queue Len : 0
Unknown Protos : 0
Rates (5 minute weighted average) :
Total Rx (Kbps) : 50344 Total Tx (Kbps) : 50904
Unicast Rx (Pkts/sec) : 108 Unicast Tx (Pkts/sec) : 121
B/Mcast Rx (Pkts/sec) : 37 B/Mcast Tx (Pkts/sec) : 18
Utilization Rx : 00.50 % Utilization Tx : 00.50 %

[Praveen_D]

Dear , Can you share both interface show config , mostly probelem with duplex or speed miss match .

[AyushGupta1]

tec11d-a4ebs03.fc.intel.com#

C1    10GbE-CX4 | Yes     Auto         Disable   0

tec11d-a4ebs03.fc.intel.com# sh lldp info remote-device c1

LLDP Remote Device Information Detail

Local Port : C1
ChassisType : mac-address
ChassisId : 08 2e 5f f0 2a 01
PortType : local
PortId : 25
SysName : tec11d-a4ebs02.fc.intel.com
System Descr : ProCurve 498358-B21 6120G/XG Blade Switch, revision Z.14....
PortDescr : C1
Pvid : 1

System Capabilities Supported : bridge, router
System Capabilities Enabled : bridge

Remote Management Address
Type : all802
Address : 08 2e 5f f0 2a 01

The above port is connected to another HP 6120 switch (tec11d-a4ebs02.fc.intel.com).

tec11d-a4ebs02.fc.intel.com# sh int c1

Status and Counters - Port Counters for port C1

Name :
MAC Address : 082e5f-f02a07
Link Status : Up
Totals (Since boot or last clear) :
Bytes Rx : 1,115,859,576 Bytes Tx : 3,685,007,040
Unicast Rx : 397,399,382 Unicast Tx : 4,032,441,244
Bcast/Mcast Rx : 1,096,459,974 Bcast/Mcast Tx : 1,609,101,937
Errors (Since boot or last clear) :
FCS Rx : 524 Drops Rx : 0
Alignment Rx : 0 Collisions Tx : 0
Runts Rx : 0 Late Colln Tx : 0
Giants Rx : 0 Excessive Colln : 0
Total Rx Errors : 2508 Deferred Tx : 0
Others (Since boot or last clear) :
Discard Rx : 0 Out Queue Len : 0
Unknown Protos : 0
Rates (5 minute weighted average) :
Total Rx (Kbps) : 51008 Total Tx (Kbps) : 50000
Unicast Rx (Pkts/sec) : 104 Unicast Tx (Pkts/sec) : 48
B/Mcast Rx (Pkts/sec) : 16 B/Mcast Tx (Pkts/sec) : 39
Utilization Rx : 00.51 % Utilization Tx : 00.50 %

tec11d-a4ebs02.fc.intel.com#

C1 10GbE-CX4 | Yes Auto Disable 0