- Community Home
- >
- Networking
- >
- Switching and Routing
- >
- Aruba & ProVision-based
- >
- Re: Output of some command in HP ProCurve
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-15-2011 09:02 PM
08-15-2011 09:02 PM
Re: Output of some command in HP ProCurve
Hi.
I looked around the attachment,but I don't know how to get statistic information of VLAN like cisco device:
CSW-2-1#show int vlan 1
Vlan1 is administratively down, line protocol is down
Hardware is CPU Interface, address is ...
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
75 packets input, 10472 bytes, 0 no buffer
Received 1 broadcasts (0 IP multicast)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 1 ignored
259 packets output, 0 bytes, 0 underruns
0 output errors, 5 interface resets
0 output buffer failures, 0 output buffers swapped out
Please tell me, is there any command in HP ProCurve show information like that?
Thanks.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-15-2011 11:54 PM
08-15-2011 11:54 PM
Re: Output of some command in HP ProCurve
not that i'm aware of..
hth
alex
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-21-2011 09:50 PM - edited 08-21-2011 09:51 PM
08-21-2011 09:50 PM - edited 08-21-2011 09:51 PM
Re: Output of some command in HP ProCurve
Hi again,
Please help me, how to know MAC address of and interface(port) in HP ProCurve?
Thanks.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-21-2011 10:00 PM
08-21-2011 10:00 PM
Re: Output of some command in HP ProCurve
sw5# sh mac
Status and Counters - Port Address Table
MAC Address Located on Port
------------- ---------------
xxxxxx-xxxxxx Trk1
xxxxxx-xxxxxx H7
sw5# sh mac h7
Status and Counters - Port Address Table - H7
MAC Address
-------------
xxxxxx-xxxxxx
hth
alex
- « Previous
-
- 1
- 2
- Next »