Output of some command in HP ProCurve

[leeffa]

Hi all,

I start to work with CLI of HP Procuve without real device. I found some documents, show some cli. but that's not enough,so, while waiting for real devices, could you please tell me output of some following commands:

- show cdp neighbors detail

- show version.

Thanks a lot.

[EckerA]

Hi,

here you go:

sw1# sh ver
Image stamp:    /sw/code/build/btm(t3a)
                Oct 17 2008 20:03:02
                K.13.45
                706
Boot Image:     Primary
sw1#

sw1# sh cdp nei detail

 CDP neighbors information

  Port : A1
  Device ID : XX XX XX XX XX XX
  Address Type : IP
  Address      : 192.168.0.2
  Platform     : ProCurve J8697A Switch 5406zl, revision K.13.45, ROM K.1...
  Capability   : Switch
  Device Port  : 1
  Version      : ProCurve J8697A Switch 5406zl, revision K.13.45, ROM K.1...

------------------------------------------------------------------------------

  Port : A2
  Device ID : XX XX XX XX XX XX
  Address Type : IP
  Address      : 192.168.0.2
  Platform     : ProCurve J8697A Switch 5406zl, revision K.13.45, ROM K.1...
  Capability   : Switch
  Device Port  : 2
  Version      : ProCurve J8697A Switch 5406zl, revision K.13.45, ROM K.1...

hth

Alex

[leeffa]

Hi.

Please help me to specify equivalent command in HP ProCurve of  some following Cisco commands, and output.

+ show ip route

+ show int vlan <number> (get detail information of  a vlan)

+ show interface description (get Description of interface)

+ show inter 

Thanks.

[AAPP Toledo]

Hi,

Please.... Here  you can found all the CISCO<=> Procurve comparative command.

SW_Archivo_Anexo# sh ip route
                                IP Route Entries
  Destination        Gateway         VLAN Type      Sub-Type   Metric     Dist.
  ------------------ --------------- ---- --------- ---------- ---------- -----
  0.0.0.0/0          10.128.24.136   2    static               0          250 
  10.128.24.128/25   DATOSARCHIVO    2    connected            0          0   
  127.0.0.0/8        reject               static               0          250 
  127.0.0.1/32       lo0                  connected            0          0   
 

******************************************************************************************

SW_Archivo_Anexo# show vlans 2

 Status and Counters - VLAN Information - Ports - VLAN 2

  802.1Q VLAN ID : 2          
  Name : DATOSARCHIVO
  Status : Port-based  Voice : No
  Jumbo : No

  Port Information Mode     Unknown VLAN Status   
  ---------------- -------- ------------ ----------
  1                Untagged Learn        Up       
  2                Untagged Learn        Down     
  3                Untagged Learn        Down     
  4                Untagged Learn        Down     
  5                Untagged Learn        Down     
  6                Untagged Learn        Up       
  7                Untagged Learn        Down     
  8                Untagged Learn        Up       
  9                Untagged Learn        Up       
  10               Untagged Learn        Up       
  11               Untagged Learn        Down     
  12               Untagged Learn        Up       
  13               Untagged Learn        Down     
  14               Untagged Learn        Down     
  15               Untagged Learn        Up       
  16               Untagged Learn        Up       
  17               Untagged Learn        Down     
  18               Untagged Learn        Down     
  19               Untagged Learn        Up       
  20               Untagged Learn        Down     
  21               Untagged Learn        Down     
  22               Untagged Learn        Up       
  23               Untagged Learn        Up       
  24               Untagged Learn        Up       
 

******************************************************************************************

SW_Archivo_Anexo# sh interfaces brief 1

 Status and Counters - Port Status

                  | Intrusion                           MDI   Flow  Bcast
  Port  Type      | Alert     Enabled Status Mode       Mode  Ctrl  Limit
  ----- --------- + --------- ------- ------ ---------- ----- ----- ------
  1     100/1000T | No        Yes     Up     1000FDx    MDI   off   0    
 
SW_Archivo_Anexo# sh interfaces 1

 Status and Counters - Port Counters for port 1                      

  Name  : PC Digitalizacion (10.128.24.146)                              
  Link Status     : Up 
  Totals (Since boot or last clear) :                                   
   Bytes Rx        : 111,644,502        Bytes Tx        : 919,931,758      
   Unicast Rx      : 322,927            Unicast Tx      : 357,849          
   Bcast/Mcast Rx  : 6778               Bcast/Mcast Tx  : 8,909,893        
  Errors (Since boot or last clear) :                                   
   FCS Rx          : 0                  Drops Rx        : 0                
   Alignment Rx    : 0                  Collisions Tx   : 0                
   Runts Rx        : 0                  Late Colln Tx   : 0                
   Giants Rx       : 0                  Excessive Colln : 0                
   Total Rx Errors : 0                  Deferred Tx     : 0                
  Rates (5 minute weighted average) :
   Total Rx  (bps) : 357496             Total Tx  (bps) : 5001024  
   Unicast Rx (Pkts/sec) : 0            Unicast Tx (Pkts/sec) : 0        
   B/Mcast Rx (Pkts/sec) : 0            B/Mcast Tx (Pkts/sec) : 1        
   Utilization Rx  : 00.03 %            Utilization Tx  : 00.50 %

******************************************************************************************

Greetings...

[leeffa]

Hi again,

How about command "show interface"? I need a full ouput to create a parser to get all interface information.

Thanks.

[Arimo]

Hi

Do you want to see full details of one interface or all of them? If one, the command would be

show interfaces <portnum>

 Status and Counters - Port Counters for port A1                     

  Name  :                                                                
  MAC Address      : 001ffe-xxxxxx

  Link Status      : Up 
  Totals (Since boot or last clear) :                                   
   Bytes Rx        : 0                  Bytes Tx        : 643,613,020      
   Unicast Rx      : 0                  Unicast Tx      : 19,091,649       
   Bcast/Mcast Rx  : 0                  Bcast/Mcast Tx  : 48,109,276       
  Errors (Since boot or last clear) :                                   
   FCS Rx          : 0                  Drops Tx        : 22,762           
   Alignment Rx    : 0                  Collisions Tx   : 0                
   Runts Rx        : 0                  Late Colln Tx   : 0                
   Giants Rx       : 0                  Excessive Colln : 0                
   Total Rx Errors : 0                  Deferred Tx     : 0                
  Others (Since boot or last clear) :                                   
   Discard Rx      : 0                  Out Queue Len   : 0                
   Unknown Protos  : 0                
  Rates (5 minute weighted average) :
   Total Rx  (bps) : 0           Total Tx  (bps) : 5029824  
   Unicast Rx (Pkts/sec) : 0          Unicast Tx (Pkts/sec) : 0        
   B/Mcast Rx (Pkts/sec) : 0          B/Mcast Tx (Pkts/sec) : 27       
   Utilization Rx  :     0 %  Utilization Tx  : 00.50 %

You can replace <portnum> with port list as well (show interfacess a1-b7) or if you want everything, just show interfaces all. And of course, port numbers like A1 refer to a modular switch, on a single box it's just a number.

[leeffa]

Hi.

I need the full output of command "show interface" because i need to know how to separate between 2 interface,

ex: in cisco device:

FastEthernet0/0 is up, line protocol is up
  Hardware is AmdFE, address is
  Description: Test
  Internet address is 10.11.0.3/24
  MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA, loopback not set
  Keepalive set (10 sec)
  Full-duplex, 100Mb/s, 100BaseTX/FX
  ARP type: ARPA, ARP Timeout 04:00:00
  Last input 00:00:00, output 00:00:00, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/75/2437850/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/40 (size/max)
  5 minute input rate 4000 bits/sec, 6 packets/sec
  5 minute output rate 11000 bits/sec, 5 packets/sec
     23438226 packets input, 1888069064 bytes
     Received 896051 broadcasts, 0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     0 watchdog
     0 input packets with dribble condition detected
     17440339 packets output, 1890934238 bytes, 0 underruns
     0 output errors, 0 collisions, 0 interface resets
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier
     0 output buffer failures, 0 output buffers swapped out
FastEthernet0/1 is up, line protocol is up
  Hardware is AmdFE, address is
  Description: OHUI
  Internet address is 10.11.14.1/30
  MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA, loopback not set
  Keepalive set (10 sec)
  Full-duplex, 100Mb/s, 100BaseTX/FX
  ARP type: ARPA, ARP Timeout 04:00:00
  Last input 00:00:05, output 00:00:03, output hang never
  Last clearing of "show interface" counters never
  Input queue: 1/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/40 (size/max)
  5 minute input rate 7000 bits/sec, 2 packets/sec
  5 minute output rate 2000 bits/sec, 3 packets/sec
     3650517 packets input, 555207068 bytes
     Received 180588 broadcasts, 0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     0 watchdog
     0 input packets with dribble condition detected
     3647836 packets output, 408367098 bytes, 0 underruns
     0 output errors, 0 collisions, 0 interface resets
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier
     0 output buffer failures, 0 output buffers swapped out

please help me!

Thank a lot.

[EckerA]

Hi,

ok.. with just "show interface" you get:

sw5# show interface

 Status and Counters - Port Counters

                                                              Flow
  Port    Total Bytes  Total Frames Errors Rx    Drops Tx     Ctrl
  ------- ------------ ------------ ------------ ------------ -----
  A1-Trk1 4,004,276... 157,619,151  0            0            off
  A2-Trk1 921,541,885  499,414,679  0            0            off
  A3      0            0            0            0            off
  A4      0            0            0            0            off
  B1-Trk2 2,776,599... 342,217,023  0            0            off
  B2-Trk2 3,281,941... 229,766,326  0            0            off
  B3      0            0            0            0            off
  B4      0            0            0            0            off
  C1      294,469,778  317,316      0            0            off
  C2      0            0            0            0            off
  C3      2,247,750... 108,259,293  16           17           off
  C4      3,450,795... 15,034,711   0            0            off
  C5      2,405,096... 9,600,108    0            0            off
  C6      3,552,205... 147,368,798  0            55           off
  C7      3,448,203... 64,653,985   0            0            off
  C8      3,259,989... 64,601,796   0            0            off
  C9      1,803,630... 74,745,461   0            30,161,251   off
  C10     2,469,029... 10,435,556   0            9            off
  C11     3,218,997... 74,119,939   3            9            off
  C12     0            0            0            0            off
  D1      3,932,098... 295,514,597  7            19           off
  D2      2,811,100... 367,766,257  17           54           off
  D3      2,892,338... 82,529,668   1            19           off
  D4      1,381,751... 419,517,687  9            67           off
  D5      1,700,185... 462,164,040  11           74           off
  D6      4,118,810... 15,677,629   0            0            off
  D7      2,289,634... 263,249,459  7            81           off
  D8      3,055,788... 184,010,374  4            55           off
  D9      2,205,425... 155,051,641  3            41           off
  D10     2,304,889... 167,045,660  8            49           off

 .....

to get something like the show interface in cisco you need:

sw5#  show interface all

 Status and Counters - Port Counters for port A1

  Name  : sw4
  Link Status     : Up
  Totals (Since boot or last clear) :
   Bytes Rx        : 1,318,069,079      Bytes Tx        : 2,686,356,928
   Unicast Rx      : 2,139,608,173      Unicast Tx      : 2,036,301,979
   Bcast/Mcast Rx  : 272,334,159        Bcast/Mcast Tx  : 4,343,579
  Errors (Since boot or last clear) :
   FCS Rx          : 0                  Drops Tx        : 0
   Alignment Rx    : 0                  Collisions Tx   : 0
   Runts Rx        : 0                  Late Colln Tx   : 0
   Giants Rx       : 0                  Excessive Colln : 0
   Total Rx Errors : 0                  Deferred Tx     : 0
  Rates (5 minute weighted average) :
   Total Rx  (bps) : 5188464            Total Tx  (bps) : 5071816
   Unicast Rx (Pkts/sec) : 65           Unicast Tx (Pkts/sec) : 46
   B/Mcast Rx (Pkts/sec) : 11           B/Mcast Tx (Pkts/sec) : 0
   Utilization Rx  : 00.14 %            Utilization Tx  : 00.14 %


 Status and Counters - Port Counters for port A2

  Name  : sw4
  Link Status     : Up
  Totals (Since boot or last clear) :
   Bytes Rx        : 3,314,964,636      Bytes Tx        : 1,901,655,975
   Unicast Rx      : 2,684,432,287      Unicast Tx      : 1,944,660,504
   Bcast/Mcast Rx  : 161,496,461        Bcast/Mcast Tx  : 3,793,635
  Errors (Since boot or last clear) :
   FCS Rx          : 0                  Drops Tx        : 0
   Alignment Rx    : 0                  Collisions Tx   : 0
   Runts Rx        : 0                  Late Colln Tx   : 0
   Giants Rx       : 0                  Excessive Colln : 0
   Total Rx Errors : 0                  Deferred Tx     : 0
  Rates (5 minute weighted average) :
   Total Rx  (bps) : 5213328            Total Tx  (bps) : 5114600
   Unicast Rx (Pkts/sec) : 49           Unicast Tx (Pkts/sec) : 45
   B/Mcast Rx (Pkts/sec) : 5            B/Mcast Tx (Pkts/sec) : 0
   Utilization Rx  : 00.14 %            Utilization Tx  : 00.14 %

 ....

hth

alex

[leeffa]

Thanks EckerA. It's very helpful for me.

In cisco device, I can use command "show ip interface brief" to get all interface of switch, include VLAN interface with ip address, status,protocol

ex:

 CSW-2-1#sho ip int bri
Interface                  IP-Address      OK? Method Status                Protocol
Vlan1                      unassigned      YES manual administratively down down
Vlan3                      unassigned      YES manual administratively down down
Vlan4                      10.11.2.2       YES manual up                    up
Vlan888                    10.11.99.199    YES manual administratively down down
FastEthernet0/1            unassigned      YES unset  up                    up
FastEthernet0/2            unassigned      YES unset  up                    up

Please tell me, how to do this in HP ProCurve?

Thanks.

[EckerA]

Well there isn't one...

Procurve doesn't has the "inteface" kind of view.

there is:

show ip

sw5# show ip

 Internet (IP) Service

  IP Routing : Disabled

  Default Gateway : 192.168.0.1
  Default TTL     : 64
  Arp Age         : 20
  Domain Suffix   :
  DNS server      :

  VLAN         | IP Config  IP Address      Subnet Mask
  ------------ + ---------- --------------- ---------------
  DEFAULT_VLAN | Disabled
  Service      | Manual     192.168.0.2     255.255.254.0
  test           | Manual     192.168.4.2    255.255.248.0
  bla           | Manual     192.168.20.2     255.255.254.0
  bla2         | Disabled

and there is:

sw5# show interfaces brief

 Status and Counters - Port Status

                    | Intrusion                           MDI   Flow
  Port    Type      | Alert     Enabled Status Mode       Mode  Ctrl
  ------- --------- + --------- ------- ------ ---------- ----- -----
  A1-Trk1 1000T-SFP | No        Yes     Up     1000FDx    NA    off
  A2-Trk1 1000T-SFP | No        Yes     Up     1000FDx    NA    off
  A3                | No        Yes     Down                    off
  A4                | No        Yes     Down                    off
  B1-Trk2 1000SX    | No        Yes     Up     1000FDx    NA    off
  B2-Trk2 1000SX    | No        Yes     Up     1000FDx    NA    off
  B3                | No        Yes     Down                    off
  B4                | No        Yes     Down                    off
  C1      100FX     | No        Yes     Up     100FDx           off
  C2      100FX     | No        Yes     Down   100FDx           off
  C3      100FX     | No        Yes     Down   100FDx           off
  C4      100FX     | No        Yes     Up     100FDx           off
  C5      100FX     | No        Yes     Up     100FDx           off
  C6      100FX     | No        Yes     Up     100FDx           off
  C7      100FX     | No        Yes     Down   100FDx           off
  C8      100FX     | No        Yes     Down   100FDx           off
  C9      100FX     | No        Yes     Down   100FDx           off
  C10     100FX     | No        Yes     Up     100FDx           off
  C11     100FX     | No        Yes     Down   100FDx           off
  C12     100FX     | No        Yes     Down   100FDx           off
  D1      100FX     | No        Yes     Up     100FDx           off
  D2      100FX     | No        Yes     Up     100FDx           off
  D3      100FX     | No        Yes     Down   100FDx           off
  D4      100FX     | No        Yes     Up     100FDx           off
  D5      100FX     | No        Yes     Up     100FDx           off
  D6      100FX     | No        Yes     Up     100FDx           off
  

there is a "HP Networking and Cisco CLI Reference Guide" attached...

hth

alex