- Community Home
- >
- Networking
- >
- Switching and Routing
- >
- Aruba & ProVision-based
- >
- Procurve 5412zl (J8726A) Fails to boot after Firmw...
-
- Forums
-
- Advancing Life & Work
- Advantage EX
- Alliances
- Around the Storage Block
- HPE Ezmeral: Uncut
- OEM Solutions
- Servers & Systems: The Right Compute
- Tech Insights
- The Cloud Experience Everywhere
- HPE Blog, Austria, Germany & Switzerland
- Blog HPE, France
- HPE Blog, Italy
- HPE Blog, Japan
- HPE Blog, Middle East
- HPE Blog, Russia
- HPE Blog, Saudi Arabia
- HPE Blog, South Africa
- HPE Blog, UK & Ireland
-
Blogs
- Advancing Life & Work
- Advantage EX
- Alliances
- Around the Storage Block
- HPE Blog, Latin America
- HPE Blog, Middle East
- HPE Blog, Saudi Arabia
- HPE Blog, South Africa
- HPE Blog, UK & Ireland
- HPE Ezmeral: Uncut
- OEM Solutions
- Servers & Systems: The Right Compute
- Tech Insights
- The Cloud Experience Everywhere
-
Information
- Community
- Welcome
- Getting Started
- FAQ
- Ranking Overview
- Rules of Participation
- Tips and Tricks
- Resources
- Announcements
- Email us
- Feedback
- Information Libraries
- Integrated Systems
- Networking
- Servers
- Storage
- Other HPE Sites
- Support Center
- Aruba Airheads Community
- Enterprise.nxt
- HPE Dev Community
- Cloud28+ Community
- Marketplace
-
Forums
-
Blogs
-
Information
-
English
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
04-18-2016 08:22 AM
04-18-2016 08:22 AM
Procurve 5412zl (J8726A) Fails to boot after Firmware uprgade to K14_58m
So, I was following the release notes, and specficially the best practices step by step from the support site for some Procurve switches I recently acquired from a surplus sale. I had no problems taking them from an early K12 series firmware to K_13_68. the bootrom was higher than the release notes said it needed to be.
After updating the flash, in the console mode it shows that the bootrom needs to be upgraded, it completes that proces then after that it stops at the initial boot prompt with IS2S0123 showing and locks solid. I have a bad feeling I may have bricked to management modules at this point, but not sure if there is any way to recover these units.
Thhe units have had all modules removed, reseated both the ram, and compact flash cards on the management modules, reseated the management modules in the chasis as well. I'm at somewhat of a loss at this point. Any help would be appreciated.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
04-19-2016 02:04 PM
04-19-2016 02:04 PM
Re: Procurve 5412zl (J8726A) Fails to boot after Firmware uprgade to K14_58m
Hello. Does it try and upgrade the bootrom every time you boot up? If so you might try a different build and have that do the ROM upgrade. If you successfully did the ROM upgrade via K.13.68 (BootROM K.12.17 or newer) you should be able to jump into K.15. xx. If that doesn't work you might be able to xmodem the ROM directly.
"IS2S0123" means the system has passed boot and memory validation and is about to load the ROM. So if that's all you get on a boot or power up you are probably toast...
Hewlett Packard Enterprise International
- Communities
- HPE Blogs and Forum
© Copyright 2021 Hewlett Packard Enterprise Development LP