- Community Home
- >
- Networking
- >
- Switching and Routing
- >
- Aruba & ProVision-based
- >
- Trunk Between Cisco Catalyst-3560-CX Series Switch...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-14-2017 08:14 AM
02-14-2017 08:14 AM
Trunk Between Cisco Catalyst-3560-CX Series Switch & HP Procurve 2510-48 Switch
Hello Everyone,
I want to configure trunk between Cisco Catalyst-3560-CX Series Switch (Layer 3 Switch) which has 12 Gigabit ethernet ports & HP Procurve 2510-48 Switch (Layer 2 Switch) which has 48 Fast ethernet ports. Both are manageable switch. However cisco is Gigabit ethernet and HP is Fast ethernet. I have 6 VLANs on cisco switch. I want to create trunk between Cisco and HP switch. I dont want to create VLANs on HP switch. I just want to trunk between them without creating VLANs on HP switch. How to verify if trunk is working fine after configuration.
Following has been configured on cisco switch
Interface IP-Address OK? Method Status Protocol
Vlan1 10.10.0.1 YES NVRAM up up
Vlan100 10.10.1.1 YES NVRAM up down
Vlan101 10.10.2.1 YES NVRAM up down
Vlan102 10.10.3.1 YES NVRAM up down
Vlan103 10.10.4.1 YES NVRAM up down
Vlan104 10.10.5.1 YES NVRAM up down
Vlan105 10.10.6.1 YES NVRAM up down
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Gi0/1, Gi0/2, Gi0/3, Gi0/4
Gi0/11, Gi0/12, Gi0/13, Gi0/14
Gi0/15, Gi0/16
100 Senior Mgmt active Gi0/5
101 ConferenceRoom active Gi0/6
102 MICM Users Admin active Gi0/7
103 Classrooms active Gi0/8
104 ETTI College active Gi0/9
105 ComputerLab active Gi0/10
Interface IP-Address OK? Method Status Protocol
Vlan1 10.10.0.1 YES NVRAM up down
Vlan100 10.10.1.1 YES NVRAM up down
Vlan101 10.10.2.1 YES NVRAM up down
Vlan102 10.10.3.1 YES NVRAM up down
Vlan103 10.10.4.1 YES NVRAM up down
Vlan104 10.10.5.1 YES NVRAM up down
Vlan105 10.10.6.1 YES NVRAM up down
GigabitEthernet0/1 unassigned YES unset down down
GigabitEthernet0/2 unassigned YES unset down down
GigabitEthernet0/3 unassigned YES unset down down
GigabitEthernet0/4 unassigned YES unset down down
GigabitEthernet0/5 unassigned YES unset down down
GigabitEthernet0/6 unassigned YES unset down down
GigabitEthernet0/7 unassigned YES unset down down
GigabitEthernet0/8 unassigned YES unset down down
GigabitEthernet0/9 unassigned YES unset down down
GigabitEthernet0/10 unassigned YES unset down down
GigabitEthernet0/11 unassigned YES unset down down
GigabitEthernet0/12 unassigned YES unset down down
GigabitEthernet0/13 unassigned YES unset down down
GigabitEthernet0/14 unassigned YES unset up down
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-20-2017 05:25 PM
02-20-2017 05:25 PM
Re: Trunk Between Cisco Catalyst-3560-CX Series Switch & HP Procurve 2510-48 Switch
Which VLAN did you want to connect to the HP switch?